Xero88 CHILLI 12 x 10 Operating Manual Download Page 24

Page: 24 / 30

User Interface

Chilli Dimmer 73-853-00 Issue 8

Page 24 of 30

Preheat

Select the

Preheat

option from the

top level menu options, and press
the  ENT  key  to  enter  the  Preheat
menu.  The  following  two  options
are available:

• Set Preheat
• Clear Preheats

Set Preheat

This option allows you to set up a
preheat level (between 0 - 20%)
for each of the dimmer channels.

Select the Set

Preheat

option from

the menu, and press the ENT key.
The screen shows:

Channel: xx

Level: xx

The cursor is shown in the

Channel

field. Press the ENT key

to move between the

Channel

and

Level

fields, and adjust the values

using the numeric keypad or
cursor keys.

Clear Preheats

This option allows you to clear the
preheat levels for all of the dimmer
channels to 0%.

Select the

Clear Preheats

option

from the menu, and press the
ENT key. The screen shows:

Push ENT key to

Clear Preheats

Press the ENT key to set all the
channel preheat levels to 0%.

Dimmer Laws

You can choose a dimmer law for
each of the dimmer channels. The
dimmer

laws

determine

the

relationship  between  the  control
value  and  the  output  value
supplied to the lamp.

The  laws  are  characterised  for
TRIAC dimmers only. On the Chilli
HF  ballast  controller,  the  results
obtained  may  be  different  from
those shown below, depending on
the ballast used.

Normal

- The standard output of

the dimmer.

Linear

- Suitable for most live or

theatrical situations.

Switch

- Output switches from

zero to full when the input reaches
50%.

Square

- For use with video

cameras.

Figure 3 - 2: Dimmer Laws

Set Laws

This  option  allows  you  to  set  up
the  dimmer  law  for  each  of  the
dimmer channels.

Select the

Dimmer Laws

option

from the top level menu options,

and press the ENT key to enter
the Dimmer Laws menu.

Select the

Set Laws

option from

the menu, and press the ENT key.
The screen shows:

Channel: xx

Law: xxxxxx

The cursor is shown in the

Channel

field.

The  channel  is  selected  using the
numeric  keypad  or  cursor  keys.
Press  the  ENT  key  to  move
between  the

Channel

and

Law

fields. When the cursor is in the

Law

field, the cursor keys cycle

through the laws.

The currently selected law for the
channel is indicated by a ‘*’, for
example:

Channel: 10

Law: Normal*

Reset Laws

This option allows you to reset the
dimmer laws for all dimmer
channels.

Select the

Dimmer Laws

option

from  the  top  level  menu  options,
and  press  the  ENT  key  to  enter
the Dimmer Laws menu.

Select the

Reset Laws

option from

the menu, and press the ENT key.
The screen shows:

Push ENT key to

reset all laws

Press the ENT key to set the state
of  all  laws  to  normal.  The  screen
will  briefly  show  a  confirmation,
and  then  return  to  the

Dimmer

Laws

screen.

Summary of Contents for CHILLI 12 x 10































Search results

Summary of Contents for CHILLI 12 x 10

Reviews:

Related manuals for CHILLI 12 x 10

Brands by name

Popular brands

Xero88 CHILLI 12 x 10, Operating Manual

Search results

Summary of Contents for CHILLI 12 x 10

Reviews:

Related manuals for CHILLI 12 x 10

Brands by name

Popular brands