background image

 

Wireless  LED  HeadLight  System  (L2SWE)                                                                                                  www.xenosys.co.kr 

 

13 

eyes to avoid the risk of permanent eye damage. 

 

C. Maintenance & Storage after use 

1. If the usage is done, press the power ON/OFF button to turn off. Then store it to the case 

after cleaning dirt or bloods for further use. 

2. Store LED light in the place free from the air with pressure, temperature, humidity, wind, ray 

of light, dirt, salinity, and ion.

 

3. Store L2SW in the place free from the declination, shack, and shock.

 

4. Store L2SW in the place free from gas, smoke, and chemical fluid.

 

5. Clean up & wash for next time use.

 

  Caution – External can be cleaned with soft cloth. In case of heavy pollution, try with a bit of 

neutral detergent and make sure to NO water or electrolyte flow into the main body.

 

6. In case of malfunctioning, stop using immediately and contact the dealer. 

7. Do not disassemble, repair, or modify the equipment by unauthorized personnel. 

  Caution- Unauthorized disassemble, repair, or modification are out of warranty. 

9. Warning for storage of battery pack 

As  Li-Polymer  battery  is  small-sized  with  high  power,  if  it  is  stored  fully  charged  condition 

for a long time, the battery lifespan can be reduced. 

(1)

 

Store it under half-charged condition in case of non-use immediately. 

(2)

 

Recommend to keep it in the dry condition with ambient temperature range of 0℃ ~ 40℃. 

Keep away from too hot or extremely cold places. 

10. Battery Service Life 

Provided  battery  can  be  charged  and  discharged  about  300  times  at  room  temperature. 

Lithium-ion  battery  is  expendables,  thus  if  the  operating  time  is  shortened  after  full 

charge, we recommend exchanging new battery. 

 

 

 

 

 

 

Summary of Contents for L2SWE



























Reviews: