manualshive.com logo in svg

Xeltek SuperPro 611S, Manual

Share
Download
Xeltek SuperPro 611S Manual Download Page 62

 
 

        SuperPro     

®

 6100 Programmer 

 

                                                                                   

www.xeltek.com

                                                            62 / 64 

1296 Kifer Rd. Suite #605 

           

[email protected]

   

Sunnyvale, CA 94086 

                Tel: +1 408-530-8080 

 

                Fax: +1 408530-0096 

 

 

Programmer not found: the programmer is not connected to the PC or connected 
improperly. Please connect it and refer to “Installation”.   
 
Programmer not ready: shut down the power switch and  turn it on again  after a  few 
seconds.   
Programmer is running: The programmer hardware is operating. Please wait until the 
operation is finished.   
 
File open error: The ‘open’ file operation has failed.   
Out of Memory: The memory overflows.   
 
Production mode isn't available for this chip: Since the production mode is dependent 
on  the  pin  check,  the  chips  without  pin  check  function  are  not  applicable  for 
production mode. 
 
Cancel production mode: Cancel the production mode.   
 
Too long file name: A too long file name is used.   
 
User cancel: The user has used the ‘cancel’ operation.   
Can't cancel: The ‘cancel’ operation has failed.   
Not a project file: The selected file is not a project file. After the software is updated 
the  software  may  not  be  able  to  identify  the  file  created  previously.  Now  the  user 
needs to create the file again. 
 

Appendix 

 
XELTEK  software  only  needs  the  minimum  technical  support.  The  program  is 
handed over to the user along with a user manual. If the user can not find a solution to 
to  his  problem,  he  can  contact  the  local  sales  agent,  the  distributor  or  XELTEK  for 
technical help. If the local sales agent or distributor can not solve your problem, you 
can  ask  XELTEK  for  technical  help  through  the  telephone  in  the  normal  working 
hours  (8:30  ---  17:30,  except  for  the  holidays  and  festivals).  You  should  get  your 
product serial number ready before you make a telephone call, otherwise we may not 
be able to answer your question.   
XELTEK  periodically  publishes  the  upgraded  software  at  the  website  of  the 
corporation. The legal user can download it and upgrade his software.  The non-user 
can  download  it  too,  but  just  can  only  be  used  for  assessment.  The  software  can  be 
obtained free through the internet.   

 
 
 
 
 

Summary of Contents for SuperPro 611S

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands