Xantrex Freedom SW 815-2012 Page 6 Installation Manual Download | Manualshive

Page: 6 / 78

background image

iv

Freedom SW Installation Guide

Important Safety Instructions

IMPORTANT:

R

EAD

AND

SAVE

THIS

I

NSTALLATION

G

UIDE

FOR

FUTURE

REFERENCE

.

This chapter contains important safety and installation instructions for the
Freedom SW Inverter/Charger (Freedom SW). Each time, before using the
Freedom SW, READ ALL instructions and cautionary markings on or
provided with the inverter/charger, the batteries, and all appropriate sections
of this guide.

NOTE:

The Freedom SW contains no user-serviceable parts. See “Warranty

and Return Information” on the Owner’s Guide for guidance.

NOTE:

Turning off the inverter/charger using the on/off switch on the front

panel will not reduce an electrical shock hazard.

ELECTRICAL SHOCK HAZARD

•

Do not expose the Freedom SW to rain, snow, spray, or bilge water.
This inverter/charger is designed for marine applications only when
additional drip protection is installed in certain orientations. See the
installation guide for information.

•

Do not operate the inverter/charger if it has received a sharp blow,
been dropped, has cracks or openings in the enclosure including if the
fuse cover has been lost, damaged, or will not close, or otherwise
damaged in any other way.

•

Do not disassemble the inverter/charger. Internal capacitors remain
charged after all power is disconnected.

•

Disconnect both AC and DC power from the inverter/charger before
attempting any maintenance or cleaning or working on any circuits
connected to the inverter/charger. See note below.

•

Do not operate the inverter/charger with damaged or substandard
wiring. Make sure that all wiring is in good condition and is not
undersized.

Failure to follow these instructions will result in death or serious
injury.

Freedom SW 3K2K InvChg Install Guide.book Page iv Wednesday, October 12, 2011 4:40 PM

«
...
4
5
6
7
8
...
»

Summary of Contents for Freedom SW 815-2012















































































Reviews:

No comments

Related manuals for Freedom SW 815-2012

Brand: La Marche Pages: 18

Brand: Zena Pages: 12

AVerCaster HD Duet

Brand: Avermedia Pages: 4

Brand: Sungrow Pages: 14

Brand: Senergy Pages: 50

Brand: ASEA Pages: 75

Brand: JRC Pages: 10

Brand: Ableconn Pages: 15

Brand: ICP DAS USA Pages: 43

Hubner Berlin TDP 0.09

Brand: Baumer Pages: 28

Brand: Enerdrive Pages: 2

Brand: StarTech.com Pages: 24

Brand: Racal Instruments Pages: 12

Brand: Mitsubishi Pages: 12

Brand: Speaka Professional Pages: 8

Brand: Green Gear Pages: 222

Teranex Mini IP Video 12G

Brand: Blackmagicdesign Pages: 22

Brand: BZB Gear Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands