background image

3

2

READ THIS FIRST

This  equipment  generates  and  uses  radio

frequency energy, and if not installed and used

properly,  that  is,  in  strict  accordance  with  the

manufacturers  instructions,  may  cause

interference to radio and television reception. It

has been type tested and found to comply with

the limits for remote control security devices in

accordance with the specifications in Sub-Parts

B  and  C  of  Part  15  of 

FCC  Rules

,  which  are

designed to provide reasonable protection against

such  interference  in  a  residential  installation.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause interference to radio or

television reception, which can be determined by

unplugging  the  equipment,  try  to  correct  the

interference  by  one  or  more  of  the  following

measures.

Reorient  the  antenna  of  the  radio/TV

experiencing the interference.

Relocate  the  console  with  respect  to  the

radio/TV.

Move the console away from the radio/TV.

Plug the console into an outlet on a different

electrical circuit from the radio/TV experiencing

the interference.

If necessary, consult your local X10 Dealer for

additional suggestions.

Your console’s telephone dialer is designed to

conform  to  federal  regulations,  and  you  can

connect it to most telephone lines. However, each

telephone or telephone device that you connect

to  the  telephone  line  draws  power  from  the

telephone line. We refer to this power draw as the

device’s ringer equivalence number, or REN.

If you use more than one telephone or other device

on the line, add up all the RENs. If the total is

more than five, your telephones might not ring. In

rural  areas,  a  total  REN  of  three  might  impair

ringer operation. If ringer operation is impaired,

remove one of the devices from the line.

Note:

 You must not connect your console to:

Coin-operated systems

Party-line systems

Most electronic key telephone systems

Your console’s telephone dialer complies with Part

68 of 

FCC Rules

. You must, upon request, provide

the FCC registration number and the REN to your

telephone company. Both numbers are shown on

the bottom of the console.

The telephone portion of your security console

has  been  tested  and  found  to  comply  with  all

applicable UL and FCC standards.

In the unlikely event that your console causes

problems on the telephone line, the telephone

company  can  disconnect  your  service.  The

telephone  company  attempts  to  notify  you  in

advance. If advance notice is not practical, the

telephone  company  notifies  you  as  soon  as

possible and advises you of your right to file a

complaint with the FCC.

Also, the telephone company can make changes

to its lines, equipment, operations, or procedures

that could affect the operation of this console. The

telephone company notifies you of these changes

in advance, so you can take the necessary steps

to prevent interruption of your telephone service.

Note: 

The security functions of this system have

not been tested by Underwriters Laboratories.

CONTENTS

INTRODUCTION ................................................................................................... 4

SETTING UP THE CONSOLE .............................................................................. 5

SETTING UP REMOTE CONTROLS ................................................................... 8

SETTING UP DOOR/WINDOW SENSORS ......................................................... 9

SETTING UP MOTION SENSORS .....................................................................12

SETTING UP REMOTE MODULES ................................................................... 15

SETTING UP FOR THE MONITORING STATION .............................................. 17

USING THE SYSTEM .........................................................................................18

TURNING LIGHTS ON AND OFF REMOTELY .................................................. 23

REPLACING BATTERIES ...................................................................................24

TO CLEAR ALL SENSORS AND REMOTES FROM THE CONSOLE ............... 25

TROUBLESHOOTING ........................................................................................26

All manuals and user guides at all-guides.com

Summary of Contents for Monitor Plus DC8700P


















Reviews: