25
24
was NOT flashing, the sensor is logged
into the next sequential zone (instead
of the same zone it was in).
To avoid this, remove the old batteries
and wait at least 4 hours before installing
the new batteries.
Motion Sensors
If any if the Console's zone indicators
flash slowly, the Motion Sensor or Door/
Window Sensor (see previous section)
for that zone has not reported in during
the last four hours. This is most likely
caused by dead batteries.
After Replacing the batteries in the
Motion Sensor, the following steps are
necessary to determine that the
Console still recognizes it.
1. Place the slide switch under the
SETUP flip door to RUN1 or RUN2.
2. Press
TEST
on the Motion Sensor.
If the appropriate zone indicator
blinks, then the Console recognized
the Motion Sensor and no further
action is necessary.
If the zone indicator didn't blink
when you pressed TEST:
1. Place the slide switch under the
SETUP flip door to INSTALL.
2. Press
TEST
on the Motion Sensor.
The Motion Sensor transmits a code
to the Console. The console
acknowledges this with a beep and
logs in the Motion Sensor.
Console
The console’s backup battery allows the
system to work during a power outage.
The
BATTERY LOW
indicator on the
console lights when you need to replace
the backup batteries.
Installed sensors, and Central Station
phone numbers are stored in Electrically
Erasable Programmable Read Only
Memory (EEPROM) which will not lose
its data even if the power is out and the
battery is dead.
Four AA alkaline batteries provide at
least 12 hours of backup. Replace the
batteries at least once a year.
To remove all sensors
and
remotes from the console's
memory:
• Set the console to INSTALL.
• Press
PANIC
,
ARM HOME
and
ARM
AWAY
at the same time.
Note:
Telephone numbers and
configuration data downloaded by the
service center (such as entry and exit
delays etc.) cannot be erased, and can
only be changed on request by the
service center.
Security Remote Controls
For the Keychain Remote use two AAA
alkaline batteries.
For the Security/Home Automation
Remote use four AAA alkaline batteries.
After replacing batteries, the following
steps are necessary to determine that
the console still recognizes the remote
control.
1. Place the console slide switch under
the SETUP flip door to
RUN2
.
2. Press
ARM
on the Remote Control.
If the system arms, the Console
recognized the Remote Control and
no further action is necessary.
If the system did not arm:
1. Place the slide switch under the
SETUP flip door to
INSTALL
.
2. Press
ARM
on the Remote Control.
The Remote Control transmits a
random code to the console. The
Console acknowledges this with a
beep and logs in the Remote
Control. If you do not hear a beep
follow the instructions on page 8 to
re-initialize the remote.
Home Automation Remote
Control
The Home Automation Remote Control
uses four AAA alkaline batteries but it
does not require any installation. Just
set its House Code dial to match the
Console and it's ready to use.
Door/Window Sensors
If any of the Console's zone indicators
flash slowly, the Door/Window Sensor
or Motion Sensor (see next section) for
that zone has not reported in during the
last four hours. This is most likely caused
by dead batteries.
After replacing the batteries in the Door/
Window Sensor, the following steps are
necessary to determine that the
Console still recognizes it.
1. Place the console slide switch under
the SETUP flip door to
RUN2
.
2. Press
TEST
on the sensor. If the
Door/Window sensor LED flashes
and the console chimes, it
recognized the sensor and no
further action is necessary.
If you didn't hear a chime when you
pressed TEST:
1. Place the slide switch under the
SETUP flip door to
INSTALL
.
2. Press and hold
TEST
for 3 seconds
then release it. The Door/Window
Sensor LED flashes twice.
3. Press
TEST
again. The Door/
Window Sensor transmits a code to
the Console. The console
acknowledges this with a beep and
logs in the code.
The Door/Window Sensor will normally
be logged into the SAME zone number
as it was before you replaced the
batteries. However, if you replace the
battery in the sensor when its zone light
REPLACING BATTERIES
All manuals and user guides at all-guides.com
