background image

XTDT AMPLIFIERS

1. Important safety instructions

This symbol indicates the presence of important user instructions 
and information that should be given particular attention so as to 
use the product properly.

This symbol indicates the presence of “

dangerous voltage

” that 

may cause the risk of electric shock. Pay the utmost attention and 
proceed cautiously. 
Please, read carefully the following - not thorough -advice for a 
correct and safe use of 

Digital Technology Series

 amplifiers.

1.  Follow  carefully  the  attached  documentation  and  keep  it  for 

future reference.

2.  Comply with the warnings.

3.  Store the packaging and check that all material is in excellent 

conditions.

4.  Do not use water near the product, do not pour water or any 

other liquid on the amplifiers. Do not use it with wet hands or 
feet into the water.

5.  Do not use next to heat sources such as radiators, stoves or 

other similar devices.

6.  Check  the  integrity  of  the  mains  cable.  Do  not  tread  on  the 

cable and do not squeeze the plug.   

7.  Connect the plug to a socket equipped with grounding. Do not 

tamper with the plug. If the plug supplied is not compatible with 
your socket, please apply to an electrician for its replacement.

8.  Connect to supply mains with  the same voltage as indicated 

on the back of the amplifier.

9.  Install the amplifiers in compliance with the instructions. 

10. Do not obstruct the air ducts.

11. Disconnect the appliance in case of storm and if unused.
12. Connect according to the instructions only.  

13. Do not connect an input signal higher than that indicated in the 

manual.

14. Do  not  connect  the  amplifier  output  to  the  input  of  another 

channel. 

15. Do not connect any output of the amplifier to power sources 

such as battery, voltage supply or outlet, regardless of wheth-
er the amplifier is on or off.

16. Keep the volume controls to a minimum during the amplifier 

switching on/off.

17. Do not remove the upper or lower cover: there is a risk of elec-

tric shock. 

18. Do not try to self-repair the appliance, but apply to qualified 

personnel. 

19. Clean with a dry cloth only. 

20. The product should be handled by skilled personnel in the fol-

lowing cases:
-   damaged mains cable or plug;
-   exposure of the product to rain or humidity;
-   some liquid has entered inside the unit;
-   an object has fallen on the unit;
-   the unit has fallen down and is damaged;
-   the product does not work correctly or shows a remark-

able change of performance. 

 
21. Careful supervision is necessary if the product is used in the 

presence of children or inexpert adults.

22. This product could produce sound levels which cause hear-

ing damage. Use the utmost care and do not operate at high 
volume level or at an uncomfortable level for a long time. 

 

Consult  an  audiometric  specialist  in  case  of  hearing  loss  or 
complaints. 

3/14

Summary of Contents for XTDT series















Reviews: