background image

might be blocked or out of range. 

False alarms triggered 

intermittently or when residents are 

cooking, taking showers, etc. 

 

Check the location of your smoke alarm (see “Installation 

Positioni

ng”).

 

 

Clean the smoke alarm (see “Maintenance”).

 

Red LED flashes and the alarm 

sounds one beep every 60 seconds.

 

The battery is low. Replace the device immediately, as the 

battery is sealed inside the device and can’t be replaced. 

 

Red LED flashes and the alarm 

sounds two beeps every 40 seconds.

 

The alarm is malfunctioning. Please clean your smoke alarm 

and  see  if  it  is  working  normally.  If  not,  replace  the  device 

immediately. 

 

FCC Statement 

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates uses and can radiate 

radio frequency energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following measures: 

-- Reorient or relocate the receiving antenna.     

-- Increase the separation between the equipment and receiver.       

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.     

-- Consult the dealer or an experienced radio/TV technician for help. 

 

Changes or modifications not expressly approved by the party responsible for compliance could void 

the user's authority to operate the equipment. 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1)  This  device  may  not  cause  harmful  interference,  and  (2)  this  device  must  accept  any  interference  received, 

including interference that may cause undesired operation. 

Environmental Protection 

Waste  electrical  products  should  not  be  disposed  of  with  household  waste.  Please  recycle  where 

facilities exist. Check with Local Authority or retailer for recycling advice. 

Summary of Contents for SD19-W














Reviews: