4x4 HDBaseT Matrix with HDCP 2.2
and 4 Low Profile PoH Receivers (70m/230ft)
MX-0404-HDBT-H2-KIT Receivers
Quickstart Guide
In the Box
Refer to the MX-0404-HDBT-H2-KIT MTRX Quickstart Guide for box
contents included with this kit.
Basic Wiring Diagram
MX-0404-HDBT-H2-KIT (matrix)
IR
Power
HDBaseT/Ethernet
HDMI/Digital Video
RS-232
Key
IR RX
Blu-ray Player
Satelitte Box
HDMI
HDMI
IR TX
IR TX
RS-232
Control System
IR Control System
IR RX
CAB-IR-LINK (Sold Seperatley)
LAN
Cat5/5e/6
Display Mirrored to
HDBaseT Output
HDMI
MX-0404-HDBT-H2-KIT (recevier)
Note: The IR RX can only
be used for source
control at the matrix.
Matrix control is not
supported.
IR RX
HDMI
IR TX
IR RX
HDMI
IR TX
Receivers
powered by
AC Mains
Power
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI, or HDBaseT
connections while the transmitter or receiver is powered on. Doing so
may cause damage to the units or connected devices.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Before Beginning
• WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other
information about the product.
• Verify that all items are included in the packaging per the
In the Box
list.
Pre Wire
1. Run a Cat5e/6/6a cable from the matrix location to the receiver
location no longer than 35m/114ft (4K) and 70m/230ft (1080p).
Terminate the cable per the
HDMI/HDBaseT Wiring
section.
2. (Optional) If using IR emitters, run the wire and terminate per the
IR
TX (Emitter) Wiring
section.
3. (Optional) If using IR receivers or an IR control system, run the wire
and terminate per the
IR RX/IR EXT (Receiver) Wiring
section.
Receiver Installation
1. Install the matrix switcher following the instructions provided in the
MX-0404-HDBT-H2-KIT MTRX Quickstart Guide.
2. Connect the
HDMI Out
on the receiver to an input on the display
using an HDMI cable from a high quality brand such as
WyreStorm
Express
.
3. Using the cable created in
Pre Wire
step 1, connect the 8-pin RJ-45
female plug to the
HDBT In
jack on the receiver.
4. (Optional) Place an IR emitter onto the display device near the
device’s IR sensor and connect the opposite end to an
IR TX
port.
5. (Optional) Connect an IR Receiver to the receivers
IR RX
port. If
using an IR control system, connect it to an
IR RX
port on the
receiver using the
WyreStorm CAB-IR-LINK
or the cable created in
Pre Wire
step 2.
6. Repeat steps for additional receivers.
Copyright © 2015 WyreStorm Technologies |
wyrestorm.com
MX-0404-HDBT-H2-KIT Quickstart Guide | 160302
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
WyreStorm’s latest 4x4 ‘Kit’; this PoH matrix with 4 receivers ensures compatibility with the latest 4K sources that require HDCP 2.2 encryption.
