Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit repair,
component replacement or complete product replacement in the event of malfunction. The decision to repair or replace will
be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and excludes normal
wear and tear or cosmetic damage.
Visit the product page located at
wyrestorm.com
for additional information on this product including important technical
information not provided in this document and warranty terms & conditions.
Specifications
Copyright © 2016 WyreStorm Technologies |
wyrestorm.com
MX-0606-PP-POH v1 Quickstart Guide | 160815
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
4 of 4
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the matrix and receiving device and
that both devices are powered on.
Note:
When using PoH, to power the receivers, verify that the HDBaseT cable is
properly terminated per the
HDMI/HDBaseT Wiring
section.
Verify that the transmitter, matrix/receiver, and display support the output
resolution of the source. Refer to
Video Resolutions
in the
Specifications
tablefor the max distance based on resolution.
• Configure
EDID Settings
to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D and/or 4K
rated.
• Verify that the HDBaseT cable is properly terminated per the
HDMI/
HDBaseT Wiring
section.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3
rd
party Device Control
• Verify that IR and RS-232 cable(s) are properly terminated per the
appropriate wiring section.
IR:
IR Wiring
.
RS-232:
RS-232 Wiring
.
• Verify that the IR emitter is located over or near the IR sensor on the device.
Move the emitter closer or further from the sensor as the IR signal can be
too strong in some cases.
• Verify that the IR receiver is in line of sight of the handheld remote.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
• Use a flashlight to locate the IR receiver behind any tinted panels on the
device being control.
Power
Power Supply
Input: 100~240V AC 50/60Hz
PoH
48V 15.4W (each HDBT output)
Max Power Consumption
125 W
Environmental
Operating Temperature
32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
Storage Temperature
-4°F ~ 158°F (-20°C ~ 70°C)
10% ~ 90%, non-condensing
Maximum BTU
426.5 BTU/hr
Dimensions and Weight
Rack Units/Wall Box
3U
Height
100mm/3.94in
Width
440mm/17.33in
Depth
340mm/13.39in
Weight
6.7kg/14.74lbs
Regulatory
Safety and Emission
CE | FCC | RoHS
Audio and Video
Inputs
6x HDMI 19-pin type A
Outputs
6x HDMI 19-pin type A (Mirrors HDBaseT) 6x HDBaseT 8-pin RJ-45 female
Audio Formats
2ch PCM | Up to DTS-HD Master Audio and Dolby TrueHD
Video Resolutions (Max)
Using HDMI
1920x1080p @60Hz 36bit (15m/50ft)
Using Cat6/6a/7
1920x1080p @60Hz 36bit (70m/230ft)
Color Depth
36bit
Maximum Pixel Clock
225MHz
Communication and Control
HDMI
EDID | DVI/D supported with adapter (not included)
HDBaseT
EDID | PoH (1way) | Bidirectional IR
Ethernet
1x 8-pin RJ-45 female | Web UI | IP Control
IR
1x IR Ext - 3.5mm (1/8in) Stereo | Matrix Control
6x IR TX - 3.5mm (1/8in) Mono | Bidirectional over HDBaseT | 6/8x IR RX - 3.5mm (1/8in) Stereo | Bidirectional over HDBaseT
RS-232
Matrix Control | Firmware Updates
