background image

SALES • COMPLETE SERVICE • PARTS • TOLL FREE: 1.888.737.8388 • FAX: 1.714.630.1422

C5 Vararam Instructions

11109660 Vararam

1

If you have any further questions you can call us at 888-737-8388

1210 N. Kraemer Blvd. Anaheim, CA 92806 / www.westcoastcorvette.com

Important Instructions,
Please Read Before Installation:

TOOLS NEEDED FOR BASIC INSTALL:
1. Flathead screwdriver
2. 6-10mm sockets
3. Pliers
4. Ramps to lift front of car

1. This system is intended to enhance your vehicle and is in no way to be
used for illegal racing on public streets or highways. It is to be used on a
race track or other controlled environment!

2. The new B-2 units are the 3rd generation of the VR-1B, these kits have been made from modified
tooling to better enhance the ease of installation as well as improve overall quality of the product. We
have included some very useful helpful hints for each step of the installation, so please read the
instructions and the added tech notes carefully before beginning the installation process.

MAIN INSTRUCTIONS

1. Disconnect the negative end to your battery

2. Remove factory air box

3. Remove factory radiator cross bar (4) 10mm bolts

4. From beneath the car, remove the air dam (2) 10mm bolts

5. Remove fan shroud (7) 7-8mm bolts, disconnect the air sensor from the shroud and pull shroud

forward to disconnect plastic tabs(these are located halfway up the shrouds front side) pull the shroud
out from the bottom of the car (pictures1&3). These tabs release with a twist, they are shaped like a
half C. You can also clip them off as they are used at the factory to hold the shroud in place as the
car goes down the line.

6. Remove the factory air box support screws from the cross-member (hex screws) located on the

frame cross-member (picture 4). These are the little nipples that stick out to hold the factory box in
place. You can use a towel and a pair of pliers to twist these out. If you do not remove these the ram
tubes WILL hit.

Summary of Contents for C5 Vararam






Reviews: