Wren DRS5004 Installation And Maintenance Manual Download Page 18

Page: 18 / 112

Installation and Connection

DRS5116

Wren

2003. 09. 06 (v 1.0)

Installation and Connection

4. Connecting & Running

4.1. Connecting Camera

(1)

Connect the CCTV camera to the DRS with the BNC cable as shown below.

<Note>

The video type for all channels should be either NTSC or PAL.

The DRS sets video signal’s impedance (75

) automatically. Impedance is set as 75

. When

connecting a device to video output, impedance will be “Hi-z” status.

Video type (NTSC/PAL) should be changed prior to installing the DRS Unit. To change the

video type, it is recommended to contact the closest local Wren distributor. When changing it,

refer to “

Appendix #2. Changing Video Type

”. Wren is not responsible for any service

warranty about a problem due to careless change.

Summary of Contents for DRS5004

















































































































Search results

Summary of Contents for DRS5004

Reviews:

Related manuals for DRS5004

Brands by name

Popular brands

Wren DRS5004, Installation And Maintenance Manual

Search results

Summary of Contents for DRS5004

Reviews:

Related manuals for DRS5004

Brands by name

Popular brands