Worx WX429 Manual Download Page 9

9

Compact Circular Saw

 

EN

working conditions and the work to 

be performed. 

Use of the power tool for 

operations different from those intended could 

result in a hazardous situation. 

5.  SERVICE

a)   Have your power tool serviced by a 

qualified repair person using only identical 

replacement parts. 

This will ensure that the 

safety of the power tool is maintained.

SAFETY INSTRUCTIONS 

FOR ALL SAWS

a)

 

DANGER: Keep hands away from 

cutting area and the blade. 

 

Keep your 

second hand on auxiliary handle, or motor 

housing .

 If both hands are holding the saw, they 

cannot be cut by the blade.

b)

  

Do not reach underneath the workpiece. 

The 

guard cannot protect you from the blade below 

the workpiece.

c) 

  

Adjust the cutting depth to the thickness 

of the workpiece.

 Less than a full tooth of 

the blade teeth should be visible below the 

workpiece.

d)

   

Never hold piece being cut in your hands 

or across your leg.

 Secure the workpiece to 

a stable platform. It is important to support the 

work properly to minimize body exposure, blade 

binding, or loss of control.

e)

   

Hold the power tool by insulated gripping 

surfaces only, when performing an 

operation where the cutting tool may 

contact hidden wiring or its own cord.

 

Contact with a “live” wire will also make exposed 

metal parts of the power tool “live” and could 

give the operator an electric shock.

f)

    

When ripping always use a rip fence or 

straight edge guide.

 This improves the accuracy 

of cut and reduces the chance of blade binding.

g)

  

Always use blades with correct size and 

shape (diamond versus round) of arbour 

holes.

 Blades that do not match the mounting 

hardware of the saw will run eccentrically, 

causing loss of control.

h)   Never use damaged or incorrect blade 

washers or bolt. 

The blade washers and 

bolt were specially designed for your saw, for 
optimum performance and safety of operation.

FURTHER SAFETY 

INSTRUCTIONS FOR ALL 

SAWS

Kickback causes and related warnings

-   Kickback is a sudden reaction to a pinched, bound 

or misaligned saw blade, causing an uncontrolled 

saw to lift up and out of the workpiece toward the 

operator.

-   When the blade is pinched or bound tightly by the 

kerf closing down, the blade stalls and the motor 

reaction drives the unit rapidly back toward the 

operator.

-   If the blade becomes twisted or misaligned in the 

cut, the teeth at the back edge of the blade can dig 

into the top surface of the wood causing the blade 

to climb out of the kerf and jump back toward the 

operator.

Kickback is the result of saw misuse and/or incorrect 

operating procedures or conditions and can be 

avoided by taking proper precautions as given below.

a)  Maintain a firm grip on the saw and position 

your arms to resist kickback forces. 

Position your body to either side of the 

blade, but not in line with the blade. 

Kickback 

could cause the saw to jump backwards, but 

kickback forces can be controlled by the operator, 

if proper precautions are taken.

b)  When blade is binding, or when interrupting 

a cut for any reason, release the trigger and 

hold the saw motionless in the material until 

the blade comes to a complete stop. Never 

attempt to remove the saw from the work 

or pull the saw backward while the blade is 

in motion or kickback may occur. 

Investigate 

and take corrective actions to eliminate the cause 

of blade binding.

c)  When restarting a saw in the workpiece, 

center the saw blade in the kerf and check 

that saw teeth are not engaged into the 

material. 

If saw blade is binding, it may walk 

up or kickback from the workpiece as the saw is 

restarted.

d)  Support large panels to minimize the risk 

of blade pinching and kickback. 

Large panels 

tend to sag under their own weight. Supports 

must be placed under the panel on both sides, 

near the line of cut and near the edge of the panel.

e)  Do not use dull or damaged blades. 

Unsharpened or improperly set blades produce 

narrow kerf causing excessive friction, blade 

binding and kickback.

f)  Blade depth and bevel adjusting locking 

levers must be tight and secure before 

making cut. 

If blade adjustment shifts while 

cutting, it may cause binding and kickback.

g)  Use extra caution when sawing into existing 

walls or other blind areas. 

The protruding 

blade may cut objects that can cause kickback.

SAFETY INSTRUCTIONS 

FOR SAWS WITH INNER 

PENDULUM GUARD

Lower Guard Function

a)  Check lower guard for proper closing 

before each use. Do not operate the saw 

if lower guard does not move freely and 

Summary of Contents for WX429

























Reviews: