Worx WX429 Manual Download Page 14

14

Compact Circular Saw

 

EN

ACCESSORIES

WX429

WX429.1

Parallel guide

1

1

Hex key

1

1

Vacuum adapter

1

1

24T TCT  Blade 

1

1

HCS Blade 

1

/

Diamond disc 

1

/

We recommend that you purchase your accessories 

from the same store that sold you the tool. Refer to 

the accessory packaging for further details. Store 

personnel can assist you and offer advice.

OPERATING INSTRUCTIONS

NOTE: 

Before using the tool, read the 

instruction book carefully.

WARNING:

Do not release the handle until the saw blade 

come to complete stop and do not touch saw blade 

while the saw blade is running.

INTENDED USE:

The tool is intended for ripping and cross-cutting 

wood and other materials in straight cutting lines, 

while resting firmly on the work piece.

ASSEMBLY AND OPERATION

 

Action 

Figure

Mounting and Removing the Blade

See Fig. A

Safety switch and On/Off trigger

See Fig. B

Cross and Rip Cutting

See Fig. C1, C2

Parallel Guide

See Fig. D1, D2

Adjusting the Cutting Depth 

See Fig. E1, E2

Adjusting the Cutting Angle

See Fig. F

Pocket /Plunge

See Fig. G1, G2

Sawdust Removal

See Fig. H

Adjusting the Base Plate

See Fig. I

WORKING HINTS FOR YOUR 

TOOL

If your power tool becomes too hot, please run your 

circular saw no load for 2-3 minutes to cool the 

motor. Avoid prolonged usage at very low speeds.

Protect saw blades against impact and shock. Cutting 

with extreme force can significantly reduces the 

performance capability of the tool and reduces the 

service life of the saw blade. Sawing performance 

and cutting quality depend essentially on the 

condition and the tooth count of the saw blade. 

Therefore, use only sharp saw blades that are suited 

for the material being cut.

Choice of blades: 24 teeth for general work, approx. 

40 teeth for finer cuts, more than 40 teeth for very 

fine cuts into delicate surfaces, diamond for tile, 

cement board, etc.

Only use saw blades recommended.

MAINTAIN TOOLS WITH 

CARE 

Remove the plug from the socket before 

carrying out any adjustment, servicing or 

maintenance.

Keep tools sharp and clean for better and safer 

performance. Follow instructions for lubricating and 

changing accessories. Inspect tool cords periodically 

and if damaged, have repaired by authorized service 

facility. Your power tool requires no additional 

lubrication or maintenance. There are no user 

serviceable parts in your power tool. Never use water 

or chemical cleaners to clean your power tool. Wipe 

clean with a dry cloth. Always store your power tool 

in a dry place. Keep the motor ventilation slots clean. 

Keep all working controls free of dust. 

If the supply cord is damaged, it must be replaced 

by the manufacturer, its service agent or similarly 

qualified persons in order to avoid a hazard.

Periodically clear dust and chips from guard and 

base to ensure proper performance.

ENVIRONMENTAL 

PROTECTION

Disposal

The machine, its accessories and 
packaging materials should be sorted 
for environmentally friendly recycling.

The plastic components are labeled for 
categorized recycling.

Summary of Contents for WX429

























Reviews: