Worx WX429 Manual Download Page 8

8

Compact Circular Saw

 

EN

GENERAL POWER TOOL 

SAFETY WARNINGS

WARNING!

  

Read all safety warnings 

and all instructions.

 Failure to follow the 

warnings and instructions may result in electric 

shock, fire and/or serious injury.

Save all warnings and instructions for future 

reference.

The term “power tool” in the warnings refers to your 

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1.    WORK AREA SAFETY 

a)   Keep work area clean and well lit. 

 Cluttered 

or dark areas invite accidents.

b)   Do not operate power tools in explosive 

atmospheres, such as in the presence of 

flammable liquids, gases or dust.

 Power tools 

create sparks which may ignite the dust or fumes.

c)   Keep children and bystanders away while 

operating a power tool.

 Distractions can 

cause you to lose control.

2.   ELECTRICAL SAFETY

a)

  

Power tool plugs must match the outlet. 

Never modify the plug in any way. Do 

not use any adapter plugs with earthed 

(grounded) power tools.

 Unmodified plugs and 

matching outlets will reduce risk of electric shock.

b)   Avoid body contact with earthed or 

grounded surfaces, such as pipes, 

radiators, ranges and refrigerators.

 There  is 

an increased risk of electric shock if your body is 

earthed or grounded.

c)   Do not expose power tools to rain or wet 

conditions.

 Water entering a power tool will 

increase the risk of electric shock.

d)

  

Do not abuse the cord. Never use the cord 

for carrying, pulling or unplugging the 

power tool. Keep cord away from heat, oil, 

sharp edges or moving parts.

 Damaged or 

entangled cords increase the risk of electric shock.

e)

  

When operating a power tool outdoors, use 

an extension cord suitable for outdoor use.

 

Use of a cord suitable for outdoor use reduces 

the risk of electric shock. 

f)

  

If operating a power tool in a damp 

location is unavoidable, use a residual 

current device (RCD) protected supply.

 Use 

of an RCD reduces the risk of electric shock. 

3.   PERSONAL SAFETY

a)   Stay alert, watch what you are doing and 

use common sense when operating a 

power tool. Do not use a power tool while 

you are tired or under the influence of 

drugs, alcohol or medication.

 A moment of 

inattention while operating power tools may 

result in serious personal injury. 

b)

  

Use personal protective equipment. Always 

wear eye protection.

 Protective equipment 

such as dust mask, non-skid safety shoes, hard 

hat, or hearing protection used for appropriate 

conditions will reduce personal injuries.

c)

    

Prevent unintentional starting. Ensure 

the switch is in the off-position before 

connecting to power source and/or battery 

pack, picking up or carrying the tool.

 

Carrying power tools with your finger on the 

switch or energising power tools that have the 

switch on invites accidents.

d)

   

Remove any adjusting key or wrench 

before turning the power tool on.

 A wrench 

or a key left attached to a rotating part of the 

power tool may result in personal injury. 

e)

   

Do not overreach. Keep proper footing and 

balance at all times.

 This enables better control 

of the power tool in unexpected situations. 

f)

    

Dress properly. Do not wear loose clothing 

or jewellery. Keep your hair, clothing and 

gloves away from moving parts.

 Loose 

clothes, jewellery or long hair can be caught in 

moving parts.

g)   If devices are provided for the connection of 

dust extraction and collection facilities, ensure 

these are connected and properly used.

 Use of 

these devices can reduce dust-related hazards.

4.    POWER TOOL USE AND CARE

 

a)

  

Do not force the power tool. Use the 

correct power tool for your application. 

The correct power tool will do the job better and 

safer at the rate for which it was designed. 

b) 

  

Do not use the power tool if the switch 

does not turn it on and off.

 Any power tool that 

cannot be controlled with the switch is dangerous 

and must be repaired.

c)

    

Disconnect the plug from the power 

source and/or the battery pack from the 

power tool before making any adjustments, 

changing accessories, or storing power 

tools.

 Such preventive safety measures reduce 

the risk of starting the power tool accidentally. 

d)

   

Store idle power tools out of the reach 

of children and do not allow persons 

unfamiliar with the power tool or these 

instructions to operate the power tool.

 

Power tools are dangerous in the hands of 

untrained users. 

e)

    

Maintain power tools. Check for 

misalignment or binding of moving parts, 

breakage of parts and any other condition 

that may affect the power tool’s operation. 

If damaged, have the power tool repaired 

before use. 

Many accidents are caused by 

poorly maintained power tools. 

f)

    

Keep cutting tools sharp and clean.

 

Properly maintained cutting tools with sharp 

cutting edges are less likely to bind and are 

easier to control. 

g)

   

Use the power tool, accessories and 

tool bits etc. in accordance with these 

instructions, taking into account the 

Summary of Contents for WX429

























Reviews: