Worx WG303E Safety And Operating Manual Download Page 21

Page: 21 / 24

Chain Saw

WG303E

TROUBLEShOOTING

Symptom

Possible

Cause

Chain saw fails to
operate

Kickback brake is activated
No power
Mains socket faulty
Extension cord damaged
Fuse faulty

Pull hand guard back in position
(Figure G)
Check power
Use another socket
Check cord, replace
Replace fuse

Chain saw operates
intermittently

Extension cord damaged
Loose connection
Internal wiring defective
On/Off switch defective

Check cord, replace
Contact service agent
Contact service agent
Contact service agent

Dry chain

No oil in reservoir
Vent in oil filler cap clogged
Oil passage clogged

Refill oil
Clean cap
Clean oil passage outlet

Kickback Brake / Run
down brake

Brake does not stop chain

Contact service agent

Chain/chain bar
overheats

No oil in reservoir
Vent in oil filler cap clogged
Oil passage clogged
Chain is over tensioned
Dull chain

Refill oil
Clean cap
Clean oil passage outlet
Adjust locking knob
Sharpen chain or replace

Chain saw rips, vibrates,
does not saw properly

Chain tension too loose
Dull chain
Chain worn out
Chain teeth are facing in the
wrong direction

Adjust locking knob
Sharpen chain or replace
Replace chain
Reassemble with chain in correct
direction

Never use tools with defective On/Off switches or defective Kickback brake (Hand Guard).
In the case of all other types of technical faults, please contact helpline or local service center.

Summary of Contents for WG303E
























Search results

Summary of Contents for WG303E

Reviews:

Related manuals for WG303E

Brands by name

Popular brands

Worx WG303E, Safety And Operating Manual

Search results

Summary of Contents for WG303E

Reviews:

Related manuals for WG303E

Brands by name

Popular brands