background image

Safety

8

Safety

Signal symbol/word definitions

The following symbols and signal words are used in this user manual.

 WARNING!

This signal symbol/word designates a hazard 

with moderate risk, which may result in death or 

severe injury if not avoided.

NOTICE!

This signal word warns of possible damage to 

property.

General safety instructions

 WARNING!

Risk of injury!

If the cabinet is assembled and/or used when a fault has occurred, 

it may cause personal injury.

 

− Do not exceed the total loading capacity of 61.37 kg. The 

cabinet is not designed to accommodate weight other than 

standard loads of storage. Refer to the chapter “Technical data” 

for the maximum load-bearing capacity of each part.

 

− Do not use the cabinet if there is any visible damage or any 

parts are defective.

 

− It is suggested that at least two competent people assemble the 

cabinet to make assembly easier and avoid injury.

 

− The cabinet may only be used with adult supervision and must 

not be used as a toy.

 

− Never store the cabinet such that there is a risk of it falling 

over, or falling from an elevated position.

 

− Do not use the cabinet as a climbing aid or tread, otherwise it 

could become imbalanced and tip over.

 

− Only set up the cabinet on flat and level surfaces; otherwise, 

there is a risk of unintended rolling and injury.

Summary of Contents for 99609

















Reviews: