WORKZONE TITANIUM 11208 Instruction Manual Download Page 24

Page: 24 / 28

AFTER SALES SUPPORT

1300 889 028 (toll free)

e-mail:

MODEL No.:

[email protected]

CSJ18LDA.9 • 11208 • 10/2019

Troubleshooting

Symptom

Possible Causes

Solution

The multi purpose

saw suddenly

stops during

operation.

Overload and battery

temperature too high

Relieve the load on the

machine immediately and

allow cooling for approx.

30 seconds by running the

machine on no-load.

Low battery capacity

Charge the battery pack.

Significantly

reduced cutting

efficiency.

Worn blade

Replace a new blade.

Poor cut quality

Blade is worn out.

Blade is assembled

incorrectly

Pushing rate is too

fast

Make sure the blade is

sharp and not broken.

Make sure the blade is

installed properly.

Push the machine slowly

Work efficiency is

low.

Blade is worn out

Change to a new blade.

Blade is not

clamped tightly by

the Blade Holder.

Blade is not inserted

into place fully.

Dismantle the blade and

reinstall it correctly.

For further inquiries or issues associated with your tool, call our

Customer Service on 1300 889 028 or email us at

[email protected]

Summary of Contents for 11208





























Search results

Summary of Contents for 11208

Reviews:

Related manuals for 11208

Brands by name

Popular brands

WORKZONE TITANIUM 11208, Instruction Manual

Search results

Summary of Contents for 11208

Reviews:

Related manuals for 11208

Brands by name

Popular brands