Worksaver SS-590 Owner'S/Operator'S Manual Download Page 9

8

Always drive down slopes; never across the face. Avoid operation on steep slopes. Slow down on sharp turns
and slopes to prevent tipping and/or loss of control. Avoid slopes when surface is wet, slippery grass or soil.

SAFETY INSTRUCTIONS 

(continued)

OPERATIONAL SAFETY (continued)

Stop loader gradually when lowering or lifting loads. Operate loader controls smoothly, avoid jerky operation.

Operate loader from operator’s seat only. Remain at controls until operating cycle is complete.

Allow for additional length of loader arms and attachment on skid steer while turning.

Be sure that people, livestock, or pets are not standing near the machine while operating.

Avoid excessive speed during operation.

ALWAYS lower loader and mixer attachment to the ground or block securely before performing any
maintenance work.

Use extreme care and maintain minimum ground speed when transporting on hillside, over rough ground and
when operating close to ditches or fences. Be careful when turning sharp corners.

Stay alert for holes, rocks and roots in the terrain and other hidden hazards. Keep away from drop-offs.

Reduce speed on slopes and sharp turns to minimize tipping or loss of control. Be careful when changing
directions on slopes. Do not start or stop suddenly on slopes. Avoid operation on steep slopes.

Before operating equipment: if you have any questions regarding the proper assembly or operation, contact
your dealer or representative.

Summary of Contents for SS-590























Reviews: