background image

6

SAFETY INSTRUCTIONS 

(continued)

This Post Hole Digger was designed for one-man operation from the operator’s seat. It is the responsibility of
the operator to see that no one is within twenty-five feet (25’) of the digger when it is started. Do not operate
the digger with another person near, or in contact with, any part of the digger, PTO driveline, or auger. Serious
personal injury or death may result if any attempt is made to assist digger operation by hand.

Keep all helpers and bystanders twenty-five feet (25’) from an operating digger. Only properly trained people
should operate this machine. It is recommended the power unit be equipped with a Rollover Protection System
(ROPS) and a seat belt that is used. Always stop the PTO, set brake, shut off the engine, remove the key,
release all hydraulic line pressure, and allow auger to come to a complete stop before dismounting tractor.
Never leave equipment unattended with the power unit running.

All things with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded
operator who recognizes potential hazards and follows reasonable safety practices. The manufacturer has
designed this digger to be used with all its safety equipment properly attached, to minimize the chance of
accidents. Study this manual to make sure you have all safety equipment attached.

If a safety shield or guard is removed for any reason, it must be replaced before the machine is again operat-
ed. Always use, and maintain in place, all power take off guards furnished with the power unit as well as the
power take off guards and shields furnished with the digger.

OPERATIONAL SAFETY

The use of any loader attachment is NOT recommended on tractor with a tricycle wheel arrangement. Tricycle
type tractors are unstable for front loader use.

When the use of hand tools is required to perform any part of assembly, installation, adjustment, maintaining,
repairing, removal, or moving the digger, be sure the tools used are designed and recommended by the tool
manufacturer for that specific task.

Never place yourself between the power unit and digger while implement is in operation.

Do not walk or work under a raised digger or attachment unless it is securely blocked or held in position. Do
not depend on the power unit hydraulic system to hold the digger or attachment in place.

A heavy load can cause instability of the power unit. Use extreme care during travel. Slow down on turns and
watch out for bumps. The power unit may need counter-weights to counter-balance the weight of the digger.

Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this
equipment. Consult your doctor about operating this machine while taking prescription medications.

Never permit any person other than the operator to ride or board the power unit or implement at any time.
ALLOW NO RIDERS!

Summary of Contents for 614HC
































Reviews: