Workrite Ergonomics FDEX 60-B02-WP Assembly/Installation Instructions Download Page 17

Page: 17 / 18

Workrite Ergonomics | 800.959.9675 www.workriteergo.com

17 of 18

Connect Power In-Feed to Power Module

Snap color coded Power In-Feed

Cable to Power Module

Connecting Power In-Feed to Building Power

Note: This step should only be performed by a professional

licensed electrician.

Based on the National Electric Code (NEC) Article 220-14,

receptacle outlets shall be calculated at 180 VA per duplex.

Workrite electrical products are rated for use in 120 V systems

which yield a duplex rating of 1.5 A. Because most applications

actual circuit usage is variable or unknown, we recommend

using a max circuit rating of 80% as a guide to determine

how many receptacles should be connected per circuit. This

translates into 8 duplex or 16 simplex outlets on a 15 AMP

circuit and 10 duplex or 20 simplex outlets on a 20 AMP circuit.

Some local codes may vary from the NEC code therefore these

are only recommendations and local codes should always be

checked and followed.

WARNING!

Always install the Power In Feed as the last step when assembling a Benching System Power Module System.

Power connection for power entry options offered with this daisy chain power system must be connected by

a commercial electrician.

Do not electrically connect to more than one source of power supply.

Always verify the electrical system is connected to one and only one source of power supply.

WIRING SCHEMATIC

4 wire 2 circuit: 2 Hots, 1 Neutral, 1 Ground

2 utility circuits share a neutral and a ground

* The National Electric Code provides recommendations to the number of receptacles that can be

connected per circuit. ECA recommends using 75% loading per circuit as a guide; please consult

with your local inspector as codes may vary in different geographic locations

1-2-G

1-2-N

Green

White

Black

Red

Summary of Contents for FDEX 60-B02-WP



















Search results

Summary of Contents for FDEX 60-B02-WP

Reviews:

Related manuals for FDEX 60-B02-WP

Brands by name

Popular brands

Workrite Ergonomics FDEX 60-B02-WP, Assembly/Installation Instructions

Search results

Summary of Contents for FDEX 60-B02-WP

Reviews:

Related manuals for FDEX 60-B02-WP

Brands by name

Popular brands