WorkPro W004532A Operator'S Manual Download Page 7

UNPACKING

SYMBOLS

The product and the packaging are not children’s 
toys! Children must not play with plastic bags, 
sheets and small parts! There is a danger of choking 
and suffocation!

WARNING!

Unpack all parts and lay them on a flat, stable surface.

Remove all packing materials and shipping devices, if 
applicable.

Make sure the delivery contents are complete and free of 
any damage. If you find that parts are missing or show 
damage do not use the product but contact your dealer. 
Using an incomplete or damaged product represents a 
hazard to people and property.

 

On the product, the rating label and within these instructions you will find among others the following 
symbols and abbreviations. Familiarize yourself with them to reduce hazards like personal injuries and 
damage to property.

Volt, (alternating voltage) 

Hertz

Watt

Per minute

Note / Remark.

Read the instructionmanual.

Wear eye protection. 

Wear protective gloves.

Do not expose to rain or 
water
           
Do not burn

V~
 
Hz

W

Millimetre

Kilogram

Decibel (A-rated)

Caution / Warning.

Wear hearing protection.

Wear a dust mask.

Wear protective, slipresis-
tant footwear.

Risk of electric shock

mm

kg

dB(A)

Switch the product off and disconnect it from the power supply before assembly, 
cleaning, adjustments, maintenance, storage and transportation.

This product is of protection class II. That means it is equipped with enhanced or 
double insulation.

WEEE symbol. Waste electrical products should not be disposed of with household 
waste. Please recycle where facilities exist. Check with your Local Authority or local 
store for recycling advice.

Do not throw the electronic waste products into the domestic waste refuse. Such 
products must be delivered to a recycling centre. 

-1

/min or min

7

Ensure that you have all the accessories and tools needed 
for assembly and operation. This also includes suitable 
personal protective equipment.

Summary of Contents for W004532A













Reviews: