background image

Opti-Link 

            

WOODWAY 

Installation and Operation 

Woodway Engineering Ltd 

  OPTINS-4.0 Rev 4 

Page 6 of 9 

December 2007 

 

Changing and Fitting the Switch Legends 

The keypad switch legends are factory fitted when customers have specified the legend layout required. A comprehensive 
list of standard legends is available on request. Users may change the legends at any time by following the procedure 
below.  

To fit the switch legends: 

Disconnect power from the switch panel. 

Before removing the bezel note the current legend layout and orientation. 

Remove the two screws at the top of the panel and one in the centre of the panel 

Place a small screwdriver blade into the hole at the top left edge of the bezel and gently lift the bezel. Slide the 
blade around the edge to prise the bezel completely away from the keypad. 

Each switch button is made up of three parts, the button pad, the legend and the lens. Remove the button to be 
changed and slide the button lens left or right to remove it from the button assembly. 

Fit the new legend in the correct orientation and slide the lens back onto the button. 

Replace all the button assemblies onto the keypad. 

Holding the keypad firmly to prevent the button assemblies from being dislodged, locate the bezel tabs into the 
slots at the bottom edge of the keypad and press the bezel firmly in place. 

Before re-fitting the screws check the action of the buttons. If necessary remove the bezel and refit. 

10 

Re-fit all the screws. Do not over tighten the screws as this may distort the plastics and prevent the correct action 
of the switches 

11 

Check that all the buttons are free and operate reliably before reconnecting the switch panel. 

Summary of Contents for Opti-Link











Reviews: