manualshive.com logo in svg

Woodward 721, Operation And Calibration Manual, Page: 17 / 52

Share
Download
Woodward 721 Operation And Calibration Manual Download Page 17

Manual 26004 

 

721DSC for Marine Propulsion Application 

Woodward

  

13

 

Chapter 5 

Entering Control Set Points 

 

 
 

Introduction 

 

Because of the variety of installations, plus system and component tolerances, set points 
input to two 721 controls could not be identical even if these 721 controls are installed in 

same engine control systems. Therefore, the 721 control must be tuned to each system for 
optimum performance. 

 

This chapter contains information on how to enter control set points through the control's 
menu system using the Hand Held Programmer. See the next chapter for prestart

-

up and 

start

-

up settings and adjustments. 

 
 

 

WARNING 

 

An improperly calibrated control could cause an engine overspeed 

or other damage to the engine. To prevent possible serious injury 
from an overspeeding engine, read this entire procedure before 
starting the engine.

 

 

 

 

Hand Held Programmer and Menus 

 
The Hand Held Programmer is a hand

-

held computer terminal that gets its power from the 

721 control. The terminal connects to the RS

-

422 communication serial port on the control 

(terminal J1). To connect the terminal, slightly loosen the right

-

hand screw in the cover over 

J1 and rotate the cover clockwise to expose the 9

-

pin connector. Then firmly seat the 

connector on the terminal into J1. 
 
The programmer does a power

-

up self

-

test whenever it is plugged into the control. When the 

self

-

test is complete, the screen will display two lines of information. This is information 

relating to the application. If it does not appear, press the ESC key. Pressing the 'ID' key will 

change the display to show the software part number and the revision level of the control. 
 

Please record this software part number and revision level because Woodward will need 

these if you ever need factory service for any control problem. 
 
The programmer screen is a four

-

line, backlighted LCD display. The display permits you to 

look at two separate functions or menu items at the same time. Use the

 

Ú

“Up/Down Arrow” 

key to toggle between the two displayed items. An “@” mark will be displayed at the left side 
of the active line. The operator can change the set point only in the active line. The BKSP 

and SPACE keys will scroll through the display to show the remainder of a prompt if it is 

longer than the display screen's 18 characters. 

Summary of Contents for 721





















































Reviews:

No comments