10
Operation
MAN0884 (08/15/2011)
OPERATION
The operator is responsible for the safe operation of
the snowblower. The operator must be properly
trained. Operators should be familiar with the tractor,
snowblower, and all safety practices before starting
operation. Read through safety rules and decals on
page 5 through page 9.
Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
Never allow children or untrained persons to
operate equipment.
Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body under-
neath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpect-
edly and cause severe injury or death. Follow Oper-
ator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.
Keep bystanders away from equipment.
Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
Never place hands or body into discharge chute
or auger to unclog. Stored energy can cause auger
to quickly rotate when unclogging occurs and
cause severe injury or amputation. Stop engine,
remove key, disconnect driveline, and carefully
unclog, using a sturdy piece of wood.
Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A P HYS ICIA N IM ME DIAT E LY IF FLU ID
ENTERS SKIN OR EYES. DO NOT DELAY.
Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
Operate tractor PTO at the rpm speed stated in
“Specifications” section.
Make sure attachment is properly secured,
adjusted, and in good operating condition.
If you do not understand any part of this manual
and need assistance, see your dealer.
Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
NOTICE
■
Be sure to complete the Pre-Operation Check
List on page 16 prior to operating this Snowblower.
PRINCIPAL COMPONENTS
The snowblower has three main operating compo-
nents. A 15" diameter auger dislodges the snow and
carries it to a central fan. The snow is then discharged
by the fan and directed away from the blower through a
controllable spout.
