Wood-mizer EG50G10 Page 12 Safety, Operation, Maintenance & Parts Manual Download

Page: 12 / 38

Safety

Safety Instructions

2-5

SBEdoc072519

Safety

Refueling and Engine Operation Safety

DANGER!

Always be sure the blade is disengaged and all

persons are out of the path of the blade before starting the
engine or motor. Failure to do so will result in serious injury.

WARNING!

Store gasoline away from sawdust and other

flammable materials. Also remove sawdust from above the
engine tank before refueling. Failure to do so may result in
serious injury.

WARNING!

Use an appropriate funnel to refuel tank.

Remove any spilled fuel from area before starting engine.
Failure to do so may result in serious injury.

WARNING!

Do not for any reason adjust the engine drive

belts or belt support bracket with the engine running. Doing
so may result in serious injury.

WARNING!

Always wear proper and necessary safety

equipment when performing service functions. Proper
safety equipment includes eye protection, breathing protec-
tion, hand protection and foot protection.

WARNING!

The engine exhaust from this product contains

chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.

CAUTION!

Do not lift the engine by the carburetor when

replacing the drive belt. Damage to the engine may result.

Summary of Contents for EG50G10







































Search results

Summary of Contents for EG50G10

Reviews:

Related manuals for EG50G10

Brands by name

Popular brands

Wood-mizer EG50G10, Safety, Operation, Maintenance & Parts Manual

Search results

Summary of Contents for EG50G10

Reviews:

Related manuals for EG50G10

Brands by name

Popular brands