Table of Contents
Section-Page
2
doc052814
SECTION 1
GENERAL INFORMATION AND SAFETY
1-1
1.1
Electrical Safety......................................................................................................... 1-1
1.2
Blade Handling.......................................................................................................... 1-2
1.3
Machine Operation .................................................................................................... 1-2
1.4
Noise Level................................................................................................................ 1-3
1.5
Motor Specifications ................................................................................................. 1-3
1.6
Technical Data........................................................................................................... 1-3
1.7
Setter Components..................................................................................................... 1-5
1.8
Control Panel Components........................................................................................ 1-6
1.9
Start Up Modes.......................................................................................................... 1-8
1.10
Blade Settings............................................................................................................ 1-9
1.11
System Parameters................................................................................................... 1-11
1.12
Diagnostic & Setup.................................................................................................. 1-12
1.13
Power Supply Specification .................................................................................... 1-12
SECTION 2
OPERATION
2-1
2.1
Machine Setup ........................................................................................................... 2-1
2.2
3" Blade Support Setup (Option)............................................................................... 2-2
2.3
Preliminary Setup ...................................................................................................... 2-4
2.4
Machine Operation .................................................................................................... 2-6
SECTION 3
MAINTENANCE
3-1
3.1
Setter Calibration....................................................................................................... 3-1
3.2
Miscellaneous ............................................................................................................ 3-1
SECTION 4
ALIGNMENT
4-1
4.1
Sensor Adjustment..................................................................................................... 4-1
SECTION 5
TROUBLESHOOTING
5-1
5.1
Error Messages .......................................................................................................... 5-1
