manualshive.com logo in svg

Wood and Douglas 1335, Operating Instructions Manual

Share
Download
Wood and Douglas 1335 Operating Instructions Manual Download Page 53

1892 1335 - Orion Radio Modem Operating Instructions -  v2.9 / Aug 2009

53

received, before regarding it as lost and a communications failure to exist.  Equivalent to the

ATIPRT

 command.

Test Message Period:

 The time which is allowed to elapse in between transmissions of the

test string in response to the 

ATI3

 command, in tens of milliseconds.

TX Priority: Don’t TX on busy channel

: Normally, the Orion will not transmit if the squelch

indicates that there is already a transmission on frequency.  However, where there is
interference, this box may be checked to transmit regardless.

Add RSSI and DQ at the end of each message:

 Check the box to append this information

to the end of every packet of user data sent.

TX Start Behaviour:

 Controls the behaviour of the Orion when it receives user serial data for

transmission on Serial Port A.  For more detail on this, refer to page 24.

When set to 

Immediately

, the transmission sequence is triggered as soon as a complete

byte is received in the transmit buffer.

When set to 

End of Message

, the transmission sequence is triggered by a break in the User

Data input, assumed to be End of Message.

When set to 

Baud Rate Dependent

, if Port A baud rate is similar to or higher than the over-

air rate, the first behaviour is followed (Immediate); if the Port A rate is lower than the over-air
rate, then the second behaviour is followed (End of Message).

The remaining two parameters only apply to Mode I Base and Outstations or Mode E
Outstations.

The Alert output:

 Can be set to respond to telemetry (I/O) alarms, housekeeping alarms (RF

link and PSU) or both, or switched off entirely.  The time for which it latches on can be set from
0 to just over 10 minutes in 10ms increments.  Alert output and permission to transmit an
alarm message are independently controlled.

The 

PSU Alarm

 boxes allow you to specify an upper and lower limit for PSU voltage

(expressed in volts rather than ADC units), and separate dwell times for each for which the
supply must exceed these limits to raise a an alarm.  Entering a voltage of zero means no
alarm.

Summary of Contents for 1335




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands