manualshive.com logo in svg

Wood and Douglas 1335, Operating Instructions Manual

Share
Download
Wood and Douglas 1335 Operating Instructions Manual Download Page 41

1892 1335 - Orion Radio Modem Operating Instructions -  v2.9 / Aug 2009

41

INTRODUCTION TO THE GRAPHICAL USER INTERFACE (GUI)

The Orion GUI is a program which runs on a PC under Windows, and provides a simple and
convenient way to set up local or remote units.  It is connected to Serial Port B of the local or
Base unit, and offers tools to manage (save, retrieve etc.) as well as to edit configurations.

v

The Orion can also be interrogated and controlled using your own equipment
and software.  AT commands (detailed in Appendix A on page 63) are used for
local units (use Serial Port A or B) and over-air commands (detailed in
Appendix B on page 75) for remote units (Serial Port B only).

Software Installation

The GUI software is provided on a CD-ROM with an automatic installer.  Insert the CD-ROM in
the PC’s CD drive to auto-run the program which installs the GUI software on your computer.  

v

If auto-run is disabled, you should run the file SETUP.EXE in the root directory of
the CD to install the software.

Follow the on-screen instructions to complete the software installation.

The GUI is now ready to run.  Keep the CD in a safe place in case it is needed again.

Notes on GUI Operation

The GUI operates in a similar way to the majority of Windows applications.  A single window
contains a number of areas, including a set of tabbed pages mainly used for unit
configuration.  A menu bar at the top deals chiefly with configuration management and test
issues.  Where an item is not available, typically because it is not relevant to the configuration
in use, it is greyed (dimmed).  A number of useful functions are duplicated as a context menu,
accessible by right-clicking over an area.  Where other windows are shown, for example when
Logging, the window must be closed to return to the main GUI.

v

Where there are checkboxes, their labels change to indicate their present state
where applicable, e.g. On when checked (ticked), Off when blank.

Passwording

Some of the features of the Orion are password-protected.  Until the correct password has
been entered, these features are disabled and shown greyed on the GUI menu and on
controls on the windows.

Layer 2 items are those features which are not in general use and should be used with care by
someone who understands their properties.  To access these, select 

Parameters > Enable

Layer 2 Parameters

 from the menu bar and enter the password.

There are also some features which would normally only be used by Wood & Douglas
personnel, for example when changing a radio module, which are accessible by selecting

Parameters > Enable Radio Parameters

 from the menu bar and entering a separate

password.  This automatically gives access to Layer 2 items as well.

Access is automatically restored to the normal level when you exit the GUI application.

Summary of Contents for 1335




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands