t
Laminate cutter
This laminate cutter is only suitable for, and hence must only be used for, cutting laminate with a maximum
width of 40.0 cm by hand, where the MDF/HDF board has a thickness of 11 mm + impact sound insulation.
The blade of the laminate cutter is made of wear-free material. Due to its special shape, the cutting blade must
not be ground or sharpened.
Re-tighten the screwed connection at the blade clamping, if necessary.
Please refer to the illustrations on pages 2 - 9 for the installation and the operation of the appliance.
Hint: If you like to cut thicker laminate, it is helpful to connect the product by using the integrated screws to a
wooden board. This will bring additional stability to the Laminte Cutter.
Operating instructions
1.
Raise the cutting blade with the handle upwards
2.
Push the laminate board against the guide edge, so that a precise cutting angle of 90° will be created.
Hint: Support the other end of the laminate board, so that it will be pushed horizontally against
the guide edge.
3.
A clean cut is achieved by pressing the cutting blade with the handle steadily downwards.
Please make sure to push the blade straight down, in order to get an optimal result.
4. Attention:
Remove the angle stop before making angular & longitudinal cuts (e.g. for the end boards).
Safety instructions:
• Operate the appliance only by using its handle; keep your fingers off the cutting area.
• Always operate the appliance alone!
• Leave the blade in its closed position, when the appliance is not in use. When opening the blade move it right
to the limit stop at rear.
• Do not make any modifications or changes to the appliance.
• Never sharpen the blade!
• Make sure that both you and the appliance have a safe position on a stable surface.
• Check before starting to work that the equipment used is properly installed (such as screwed connections).
• Make sure your clothing fits tightly (especially the sleeves) and that you wear eye protection.
• Keep children out of your workshop and store your equipment and tools in a secure place.
• Never let inexperienced personnel work with your equipment and tools without duly supervising and
instructing them.
• Always work methodically, in a concentrated fashion and with sufficient lighting.
Guarantee
Dear DIY enthusiast, for this wolfcraft
®
product, we give you a
5 year guarantee.
wolfcraft
®
provides you with a replacement free of charge should damage occur during the guarantee period as
a result of material defects. The guarantee period commences on the date of purchase. Please ensure that the
guarantee card is fully completed or keep the invoice in a safe place. A requirement for the validity of this
guarantee is that the purchased appliance is only used around the home, a correct handling and the use of
original wolfcraft
®
spare parts. Claims can only be asserted under the guarantee if the guarantee card has
been fully completed.
11
Bdal 6936.000 06.04.2010 15:49 Uhr Seite 11
Summary of Contents for LC 300
