background image

3040530_201503

21

Checklist 

Recommended checklist for hygienic operation and maintenance of air handling systems

Activity

Action if required

Months

Outdoor and exhaust air apertures
Structural units/appliance casing

Check for contamination, damage and 

corrosion

Clean and repair

12

Air filter

Check for impermissible contamination and 

damage (leaks)

Replace affected air filters if last filter stage 

replacement was within last 6 months, 

otherwise replace entire filter stage

3

Steam humidifier

Wash with cleaning agent,

flush and dry the humidification chamber, 

disinfect if required

6

Check steam lance for deposits

Clean

6

Check the hygiene level

6

Heat exchanger

Check for contamination, damage and 

corrosion

Clean and repair

3

Check the function of the siphon

Repair

3

Check the hygiene level

6

Fan

Check for contamination, damage and 

corrosion

Clean and repair

6

Heat recovery

Check condensate pan and mist eliminator for 

contamination, corrosion and correct function

Repair

3

Check the function of the siphon

Repair

3

Check the hygiene level

12

Air pipes and silencer

Check silencer for contamination, damage and 

corrosion

Repair

12

Terminal unit

Check terminal unit and outdoor air filter for 

contamination

Replace air filter, clean unit

3

Check heat exchanger in terminal units without 

air filter for contamination

Clean (vacuum cleaner)

6

Replace air filter

12

Summary of Contents for KG Standard

























Reviews: