Wolf I363418 Installation Instructions Manual Download Page 10

10

I N S T A L L   D U C T   C O V E R

1)

Duct cover must be installed to

ceiling prior to hood installation

2)

Use (4) ⁄" x 3" lag screws provided

with hood to attach duct cover to ceil-
ing frame work.  See page 3 for addi-
tional dimension information.

3)

Install additional #10 x 2" screws

for support along top edge of duct-
cover and ceiling.

4) 

Install (4) 5/16" bolts, provided

with duct cover, through hood
mounting holes into bottom edge of
duct cover.  Use 5/16" nuts supplied
with duct cover and tighten on bolts.
Use #12 x 7/8" hex head self tapping
screws provided with duct cover to
attach duct cover to hood assembly

P

R O

S

E R I E S

I

S L A N D

H

O O D S

I

N S T A L L A T I O N

I N S T A L L   H O O D   F I L T E R
A N D   D R I P   C U P S

Hood Filters and Drip Cups Install

1)

Reinstall hood filter center bank

with screws removed prior to installa-
tion of hood assembly.

2)

Remove all packaging material

from filters and drip cups.

3)

Slide drip cups along bottom edge

of hood opening so lip overhangs
slightly. 

4)

Lift filters into place.  Lines of fil-

ters must run vertically and align with
drip cups.

5) 

Adjust filters to fill space by sliding

filters left to right.

CAUTION

Installing a duct cover assembly
will impact all aspects of hood
installation including hood loca-
tion, ducting, electrical place-
ment and adequacy of mounting
surfaces.

I N S T A L L   L O G O

The nameplate is not pre-assembled

because there are various locations that

the logo can be installed. Additionally,

some customers prefer not to have a

nameplate on their hood. For your

convenience, Wolf has created a tem-

plate for a standardized logo location.

Please see the back page of these

installation instructions for Wolf logo

template.

1)

Decide on the location for the

nameplate.

2)

Clean mounting area with rubbing

alcohol.

3)

If desired, cut-out template for

nameplate location.

4)

Fold template, locate placement on

hood and tape to hood surface.

5)

Check alignment and adjust if nec-

essary.

6)

Remove backing paper from name-

plate.

7)

Position nameplate in template

cutout and press into place.

8)

Remove template and any tape

residue.

OPTIONAL

DUCT

COVER

     1/4" x 3" Lag Screw

5/16" SS Nut

   5/16" SS Screw

                       #1/4" x 7/8" #12

                   self-tapping hex screw

                       2" #10 hex screw

Duct cover installation 

Summary of Contents for I363418
















Reviews: