manualshive.com logo in svg

Wolf CTI Series, Troubleshooting Manual, Page: 8 / 9

Share
Download
Wolf CTI Series Troubleshooting Manual Download Page 8

Page 8

Induction Cooktop (CTI) Series

Induction Cooktop (CTI) Series

Troubleshooting Guide

5-8

#821684 - Revision B - March, 2013

LED board failure.

Action:  Perform LED test #1 and if all 
LEDs work, reset error. 
Action:  If one of the LEDs fails to illuminate
change the Glass Assy.

Induction generator failure.
Action:  Change affected generator board.

Induction generator failure.
Action:  Change affected generator board.

1. Induction generator failure.

Action:  Perform Heatsink test #4 and if
appears ok, reset error and test operation

2. If error returns. 

Action:  Change affected generator board.

Effected burner is not
available. 

The effected burner will
shutdown.  

The effected burner will
shutdown. 

The effected burner will
shutdown.

2

2

2

2

2

2

2

2

2

2

2

2

2

2

E30

E31

E32

E33

E34

E40

E41

E42

E43

E44

E45

E50

E51

E52

Generator 1:
Burner (F,FR,FC)
‘ON LED’ Failure

Generator 1:
Burner (R,RR,RC)
‘ON LED’ Failure

Generator 2:
Burner (RL) ‘ON
LED’ Failure

Generator 2:
Burner (FL) ‘ON
LED’ Failure

Generator 3:
Burner (RR) ‘ON
LED’ Failure

Generator 1:
Burner (R,RR,RC)
sensor shorted.

Generator 2:
Burner (RL) sensor
shorted. 

Generator 3:
Burner (RR) sen-
sor shorted.

Generator 1:
Burner (R,RR,RC)
sensor open.

Generator 2:
Burner (RL) sensor
open. 

Generator 3:
Burner (RR) sen-
sor open.

Generator 1:
Open heat sink
thermistor.

Generator : Open
heat sink thermis-
tor.

Generator 3:
Open heat sink
thermistor.

ERROR

PRIORITY

NOTES

POSSIBLE SOURCE(S) OF

FAILURE / ACTION REQUIRED

DISPLAYED

ERROR #

ERROR

CONDITION

Summary of Contents for CTI Series










Reviews:

No comments