manualshive.com logo in svg

Wolf BM-Solar, Installation And Operating Instructions Manual

Share
Download
Wolf BM-Solar Installation And Operating Instructions Manual Download Page 3

3061916_0611

3

The following symbols are used in conjunction with these important 

instructions  concerning  personal  safety  as  well  as  operational 

reliability.

"Safety instructions" are instructions with which you must comply 

exactly, to prevent injury and material losses.

Danger through 'live' electrical components. 

NB Switch OFF the ON / OFF switch before removing the 

casing.
Never touch electrical components or contacts when the ON / OFF 

switch is in the ON position. This brings a risk of electrocution that 

may cause injury or death.
The main supply terminals are 'live' even when the ON / OFF 

switch is in the OFF position.

This  indicates  technical  instructions  that  you  must  observe  to 

prevent material losses and boiler malfunctions.

NB

Safety instructions

The  appliance  and  control  unit  accessories  comply  with  the 

following regulations:

EC Directives

-  2006/95/EC  Low Voltage Directive

-  2004/108/EC  EMC Directive

EN Standards

-  EN 55014-1  Interference emissions

-  EN 55014-2  Resistance to jamming

-  EN 60529

Standards / Directives

Safety instructions / Standards

Summary of Contents for BM-Solar





















Reviews:

No comments

Brands by name

Popular brands

Load more brands