30
72V Li-ION POWER 34-37-40
Servicing
EN
Cleaning the grass collector (Fig.
T V W
)
Note
It is best to clean the grass collector directly
after mowing.
Î
Raise the delector lap
T 1
.
Î
Remove the grass collector
T 2
.
Î
Lower the delector lap again
T 3
.
Î
Empty the grass collector
W 1
.
Î
Clean the fabric collection bag including the frame
with water or a hand brush.
Î
In particular, clean the area beneath the ill level
indicator
V 3
.
Î
Allow the fabric collection bag to dry before the
next use.
Transport and storage (Fig.
X
)
DANGER !
Risk of injuries due to the rotating mower
blade.
¾
Before transport or storage, switch off
the lawnmower and wait until the mower
blade comes to a standstill.
Î
Switch the lawnmower off and wait until the motor
blade comes to a standstill.
SAFETY ROUTINE
¾
Open the cover
O 1
.
¾
Turn the safety key clockwise until it reaches
position "
0
"
P
2
, then remove it.
¾
Use the power pack release device
O
5
.
¾
Remove the power pack
O
2
.
¾
Close the cover
P
3
.
Î
Secure the lawnmower suficiently to prevent its
unintentional slipping if you are transporting it in or
on a motor vehicle.
Î
To make it easier to stow the lawnmower, you can
fold the handle together
X
.
Î
To do this release the two upper quick release
levers together with the threaded pins
X 1
and
screw them out by approximately 5 mm. When
doing so hold the top part of the handle irmly, as
otherwise you could trap your hand or ingers.
Î
Fold the top part of the handle down
X 2
.
Attention !
If you fold the handle bar forwards, the cable can
become damaged.
Î
Release the two bottom quick release levers
X 3
.
Î
Fold both handles forwards and support them on
the front wheels of the lawnmower
X 4
.
3
This allows you to easily carry the lawnmower via
its handle or to move it to a secure location for
storage
X 5
(see arrow).
Storage during winter
Î
Thoroughly clean your lawnmower after every
mowing season.
Î
Arrange for a specialist workshop to check your
lawnmower in Autumn.
Î
Store the lawnmower in a clean and dry room.
Î
Protect the lawnmower against rust during long
storage periods in winter.
Î
Never store the power pack inside the lawnmower!
Replacing the mower blade (Fig.
Y
)
WARNING !
Risk of injuries.
¾
Arrange for a specialist workshop to
replace the mower blade.
¾
Only work on the mower if the motor is
stationary.
¾
War suitable safety gloves.
Î
Switch the lawnmower off and wait until the motor
blade comes to a standstill.
SAFETY ROUTINE
¾
Open the cover
O 1
.
¾
Turn the safety key clockwise until it reaches
position "
0
"
P
2
, then remove it.
¾
Use the power pack release device
O
5
.
¾
Remove the power pack
O
2
.
¾
Close the cover
P
3
.
Attention !
Grinding the mower blade can result in an
imbalance. Have a specialist workshop check for
imbalance.
Note
To change the mower blade a torque wrench
with a 10 mm socket (M6) is required. Screw
tightening torque: 6–7 Nm
Y
.
Summary of Contents for 72V Li-ION POWER 34-37-40
