4
To override remote commands from any mobile devices, unplug the unit.
Federal Communications Commission (FCC) Compliance Notice
FCC ID: A5UEICHRB01
This module complies with Part 15 of the FCC Rules. The Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2. This device must accept any interference received, including Interference that may cause undesired operation.
Under FCC regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by FCC. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication. The radio transmitter
FCC: A5UEICHRB01 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain
and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with these devices.
One of the below two Antenna con
fi
guration will be used:
Table 1: Molex Antenna Con
fi
guration
Antenna Type
ANT Chain
ANT MFG
Antenna Part#
Maximum Gain (dBi)
Required Impedance
FPC - Flexible printed circuit
0
Molex
1461530150
3.2dBi(2.4 – 2.5 GHz)
4.75dBi (5.15 – 5.85 GHz)
50 ohms
FPC - Flexible printed circuit
1
Molex
1461530150
2.8dBi(2.4 – 2.5 GHz)
4.2dBi (5.15 – 5.85 GHz)
50 ohms
Table 2: Antenova Antenna Con
fi
guration
Antenna Type
ANT Chain
ANT MFG
Antenna Part#
Maximum Gain (dBi)
Required Impedance
FPC - Flexible printed circuit
0
Antenova
SRF2W021-50
2.8dBi(2.4 – 2.5 GHz)
5.1dBi (4.9 – 5.9 GHz)
50 ohms
FPC - Flexible printed circuit
1
Antenova
SRF2W021-150 2.8dBi(2.4 – 2.5 GHz)
5.1dBi (4.9 – 5.9 GHz)
50 ohms
FCC Notice
•
Changes or modi
fi
cations not expressly approved by Whirlpool Corporation could void the user’s authority to operate the equipment.
•
The antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between
the radiator (antenna) and all persons at all times and must not be co-located or operating in conjunction with any other antenna or
transmitter.”
Part 15B compliance statements for digital devices:
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates; uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC RF radiation exposure limits for general population, the antenna(s) used for this transmitter
Must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all
times and must not be co-located or operating in conjunction with any other antenna or transmitter.
Connected Appliance Regulatory Notices
