background image

7

Limited Warranty

If Leisure Technologies determines that you are covered by a warranty as set in the 

Australian consumer law the company shall at its expense: (a) repair the product, 

or replace the product with a new unit (which may have used refurbished parts of 

similar quality); (b) ship the repaired or replaced unit back to you; (c) warrant the 

repaired or replaced product for a reasonable period; and/or (d) refund money paid 

for the product. The Company has the discretion as to which remedy applies.

Warranty period

The warranty period starts on the date of purchase and ends 24 months later. For the 

purpose of this limited warranty, the date of purchase is the date indicated on the 

original bill of sale or receipted invoice for the product from the vendor from which 

you acquired this product.

How to get warranty service

During the warranty period, if you wish to return a defective product you may 

contact us via www.witi.com.au. You may then return the defective product to the 

address given accompanied by an acceptable proof of purchase (a bill of sale or 

receipted invoice).

What is not covered

The limited warranty does not cover a product:
•  for which you are not the original purchaser;
•  that is damaged by using in a way that was unreasonable or unintended;
•  that is returned after the applicable warranty period set out above has 

expired;

•  that has been installed other than per the product installation guidelines;
•  that has been maintained, altered or modified, opened or repaired, other 

than by the company or by a company authorised service centre;

•  that has been physically damaged, other than by the company or a company 

authorised service centre.

To the extent permitted by law, Leisure Technologies, its directors, officers, 

employees, suppliers and agents, shall not be liable for injury to persons or property, 

or for any indirect, special, incidental or consequential, punitive or exemplary 

damages and liability and shall be limited to the amount you paid for the product.

Disclaimer

•  WiTi products are designed for installation by reasonably competent consumers. 

Consumers are taken to have sufficient knowledge of the intended caravan or 

trailer unit and its appropriateness for the installation of any WiTi products.

Summary of Contents for 326-1









Reviews: