Wisenet PWRDR48480 Quick Start Manual Download Page 3

QSG_SWT-G0803MG   

08/12/2019

   PAGE 3

QUICK START GUIDE 

SWT-G0803MG SERIES

Regulatory Compliance Statement

Product(s) associated with this publication complies/comply with all applicable regulations. Please 
refer to the Technical Specifications section for more details.

Warranty

Hanwha Techwin warrants that all products are free from defects in material and workmanship for 
a specified warranty period of 3 years from the invoice date. Hanwha Techwin will repair or 
replace products found by to be defective within this warranty period. Shipment expenses are to 
be covered by the customer. This warranty does not cover product modifications or repairs done 
by persons other than approved personnel, and this warranty does not apply to products that are 
misused, abused, improperly installed, or damaged by accidents.

Disclaimer

Information in this publication is intended to be accurate. shall not be responsible for its use or 
infringements on third-parties as a result of its use. There may occasionally be unintentional errors 
on this publication. reserves the right to revise the contents of this publication without notice.

Summary of Contents for PWRDR48480

















Reviews: