Winyuan 2E1-2ETH User Manual Download Page 15 | Manualshive

Page: 15 / 20

background image

2E1 to 2Eth Converter

１５

Note : When Ethernet cable at the Eth interface is longer, two pins of

receiving signal must be connected to one UTP and two pins of sending signal

are connected to one UTP.

6. Bottom panel

2 DIP switches

ON --

indicating E1 signal is grounded

OFF

—

indicating E1 signal is not grounded

SW1: receiving signal grounded

SW2: sending signal grounded

Notice: On the whole E1 link, assure only one termination is grounded.

The rack device has these two switched on the back of casette side.

Hanging function (optional)

If needing hanging function, please indicate in order list.

«
...
13
14
15
16
17
...
»

Summary of Contents for 2E1-2ETH





















Reviews:

No comments

Related manuals for 2E1-2ETH

Brand: ICP DAS USA Pages: 4

Brand: XS Scuba Pages: 4

Brand: Net Optics Pages: 15

Brand: Humandata Pages: 10

Brand: Premier Pages: 12

Brand: B&K Pages: 2

Brand: Lika Pages: 2

Brand: POWER ON BOARD Pages: 13

Brand: J-Tech Digital Pages: 34

Brand: Vortex Pages: 179

Popcorn Hour A-410

Brand: Syabas Technology Pages: 95

GearLite FDB-9649-LC

Brand: Ross Pages: 22

Q.VOLT-G2 HYB-4.6kW.1.1

Brand: Q CELLS Pages: 118

Brand: DANE-ELEC Pages: 2

Brand: DX Engineering Pages: 4

Brand: T4T Pages: 42

Brand: Extron electronics Pages: 62

10/100BASE-TX to 100BASE-FX Media Converter

Brand: D-Link Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands