manualshive.com logo in svg

Wintex Agro 1000S, Instruction Manual

Share
Download
Wintex Agro 1000S Instruction Manual Download Page 24

P A G E

 | 

24

 

 

 

 
 

 

Wintex Agro, Vilhelmsborgvej 8C, DK-7700 Thisted 

+45 97990800, [email protected], www.wintexagro.com

 

202203 

4.f.  ADJUSTMENT OF THE HYDRAULICS

 

 

Adjusting the main pressure 
Start the motor with max. r.p.m. Press the main valve. The manometer must show 80-120 bar. On soil samplers with a display the pressure 
is shown electronically. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

The excess-pressure valve which is located under the red cap is for adjusting the main pressure. The main pressure is preset on 120 bar. It 
must only be adjusted after signing a written agreement with Wintex Agro. 

 

 
 

 

 

 
 
 
 
 
 

Adjusting the pressure of the probe 
Loosen the lock nut. Adjust the pressure with a 6 mm hex key. Pressure will rise when turning to the right and lower the pressure by turning 
to the left. If the hammer will not move down, or if the soil sampler is lifted of the ground when sampling, the pressure must be lowered. 
When taking a 0-15 cm sample it can be advantageous to lower the probe pressure which will result in a better sample.  

 
 
 
 
 
 
 
 

 

 
 
 
 

 

Summary of Contents for 1000S

































Reviews:

No comments

Brands by name

Popular brands

Load more brands