Wintex Agro 1000S Instruction Manual Download Page 21 | Manualshive

Page: 21 / 32

background image

P A G E

|

21

Wintex Agro, Vilhelmsborgvej 8C, DK-7700 Thisted

+45 97990800, [email protected], www.wintexagro.com

202203

4.b. ADJUSTMENT OF CHAIN FOR ROTATION

Loosen the four screws with a 4 mm hex key.

Then adjust the chain for rotation by turning the insex bolt (clockwise to tighten the chain, counter-clockwise to loosen the chain). When the
chain is adjusted correctly, the four screws must be tightened again. Use a 4 mm hex key.

4.c. ADJUSTMENT FOR CHAIN FOR PROBE UP OR DOWN

Move the probe approximately 20 cm down. Activate the emergency stop to stop the soil sampler, and turn off the engine. The chain can
now be adjusted by tightening the bolts.

«
...
19
20
21
22
23
...
»

Summary of Contents for 1000S

































Reviews:

No comments

Related manuals for 1000S

Brand: Rain Bird Pages: 2

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

Brand: Baileigh Industrial Pages: 40

Brand: Bard Pages: 36

Brand: Bard Pages: 2

Brand: Bard Pages: 30

Brand: Bard Peripheral Vascular Pages: 44

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Harken Pages: 4

Brand: Harken Pages: 2

TERRA FORCE BOOM

Brand: Hardi Pages: 40

Brand: Harken Pages: 4

QuickSlide HemaPRO

Brand: Hardy Diagnostics Pages: 2

Brand: Hardt Pages: 2

Brand: JBSYSTEMS Light Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands