WATER DISPOSING OPTIONS
6
7
CONTROL PANEL
POWER ON/OFF (1)
Pressing button once turns the unit "ON"
and pressing it again turns the unit "OFF".
COMFORT (2)
When the unit is turned on or by pressing button
once, operation begins in comfort mode.
"At" will appear in the
display(7)
and the
comfort indicator(8)
will light up. In this setting,
humidity level is adjusted for optimum comfort
with no manual adjustment needed. When
pressing the button again, comfort mode is
turned off and the unit will adjust humidity
level based on the humidity level entered.
HUMIDITY (3)
To set desired humidity level when not in comfort
mode, push this button until desired humidity level
is reached. The humidity levels will adjust in
increments of 5% beginning at a low of 35%
and reaching a maximum of 70%. Humidity will
show in the display when adjusting humidity.
When humidity level has reached 70%, pushing
once more will set unit into continuous mode.
Continuous mode will run the unit continuously
until it is turned off or until another setting is inputted.
When continuous mode is programmed, “On”
will be displayed.
TIMER (4)
By pressing this button, the unit will run until the
desired time expires. Timer range is between 1
and 12 hours with increments of 1 hour. The
desired time remaining until shut off is shown in
the
display(7)
. Please note display shows setting
time temporarily before returning to desired
humidity level display.
FAN SPEED (5)
By pressing this button, fan speed will change.
The
indicator(9)
of selected fan speed will light
(High or Low). In Comfort Mode, fan speed will
not be set as the setting will adjust the fan speed
automatically.
PUMP ON/OFF (6)
Pump "ON" is an optional setting when using
a drain hose to remove the collected water
automatically. When the pump function is on,
the
indicator(10)
will light on. The pump button
should be off at all times except when using the
pump to remove collected water (See Page 7,
Option 3). After installing hose correctly to pump
drain, push the button for automatic water removal.
If the pump button is pressed when using other
disposal options, E3(Error message – See page
10) will be displayed. If other disposal options
are needed, push the pump button again to turn
off the pump function.
BUCKET FULL INDICATOR (7)
When the collection bucket full, bucket full
indicator will light on. The unit will not run with
the bucket full. Dispose of water and replace
bucket properly.
OPTION 1, EMPTYING MANUALLY
1. Pull out the bucket, grasping upper and
lower handles.
2. Carry the bucket by grasping the inside
handle of the bucket.
3. After emptying the bucket, replace the
bucket in the dehumidifier.
NOTE: Dehumidifier will not work when the
BUCKET FULL light is on or without the
bucket properly placed in the unit.
OPTION 2, GRAVITY DRAIN HOSE
(Garden Hose Not Provided)
1. Take off GRAVITY DRAIN CAP by turning
the cap counterclockwise. (Fig.1)
2. Remove DRAIN CONNECTOR from the
bucket. (Fig.2)
3. Next, screw the DRAIN CONNECTOR
to a standard garden hose by turning
clockwise. (Fig.3)
4. Reattach the DRAIN CONNECTOR end
of garden hose to the dehumidifier (Fig.4)
then check hose for kinks or obstructions.
The position of the hose at the floor drain
must be lower than DRAIN CONNECTOR.
5. Keep the DRAIN CAP for future use when
emptying bucket manually.
OPTION 3, PUMP DRAIN
1. Remove the PUMP DRAIN CAP by turn-
ing clockwise (Reverse thread). (Fig.1)
2. Remove the drain-hole PLUG by pulling out
while pressing in on the coupler. (Fig.2)
Keep the DRAIN CAP and PLUG for future use.
3. Feed the 1/4-inch hose provided through
the hole in the DRAIN CAP. (Fig.3)
4. Insert the end of hose into the drain hole
(Fig.4), then screw DRAIN CAP back
onto the unit. Place the other end of the
hose in the location you want the water to
go: to a floor drain, a water container, or
through a basement window to the
outdoors. (Pump can lift water up to 15
feet above the unit.) Check hose for kinks
or other obstruction.
Fig.1 Fig.2
Fig.3 Fig.4
Fig.1
Fig.2
B
Pressing
Fig.3
Fig.4
5. In the unlikely event the hose comes
loose during pump operation due to
vibration, re-attach hose to continue
automatic pump removal of water.
CAUTION: Do not remove the
bucket while the pump is operating. This
will cause the dehumidifier to stop operat-
ing and result in an “E3” error message.
ALSO: The pump drain hose should not
be both under water AND at a height
that is above the dehumidifier. This can
cause a “back flow” to the dehumidifier
and cause the dehumidifier to stop work-
ing resulting in an “E3” error message.
Following an “E3” error, the unit must be
unplugged and reset to operate. (See
Error Code section of this manual.)
2
1
8
6
5
9
4
3
10
11
7
www.sylvane.com 1-800-934-9194
