background image

Quick Start Guide of Digital Video Recorder 

14 

10 

JOG SHUTTLE 
Control 

Move the active selection in a menu. The inner ring will move the selection up and 
down; the outer ring will move it left and right.   
In Playback mode, the inner ring is used to jump 30s forward/backward in video 
files. The outer ring can be used to speed up/slow down the video.     
In Live View mode, it can be used to cycle through different channels. 
In PTZ control mode, in can control the movement of the PTZ camera. 

 

Front Panel4: 

 

Description of Front Panel 

No. 

Name 

Function Description 

POWER ON/OFF 

Power on/off switch. 

IR Receiver

 

Receiver for IR remote 

Status 

Indicators 

ALARM 

Turns red when a sensor alarm is detected. 

READY 

Ready  LED  is  normally  blue,  indicating  that  the  device  is 

functioning properly. 

STATUS 

Turns blue when device is controlled by an IR remote. 

Turns  red  when  controlled  by  a  keyboard  and  purple  when  IR 

remote and keyboard is used at the same time. 

HDD 

Flashes red when data is being read from or written to HDD. 

MODEM 

Reserved for future usage. 

TX/RX

 

Flashes blue when network connection is functioning properly. 

GUARD 

Guard LED turns blue when the device is in armed status; at this 

time, an alarm is enabled when an event is detected.   

The LED turns off when the device is unarmed. The arm/disarm 

status  can  be  changed  by  pressing  and  holding  on  the  ESC 

button for more than 3 seconds in live view mode. 

DVD-R/W   

Slot for DVD-R/W. 

Control 

Buttons 

DIRECTION

 

The DIRECTION buttons are used to navigate between different 

fields and items in menus. 

In the Playback mode, the Up and Down button is used to speed 

up  and  slow  down  recorded  video.  The  Left  and  Right  button 

will select the next and previous record files. 

In Live View  mode, these buttons can be used to cycle through 

channels. 

In  PTZ  control  mode,  it  can  control  the  movement  of  the  PTZ 

camera. 

ENTER 

The  ENTER  button  is  used  to  confirm  selection  in  any  of  the 

Summary of Contents for CW-AR505-8






































Reviews: