background image

5

To toggle between satellites when subscribing to multi-satellite programming—

While in 

Sleep Mode

, the MV-4002 will toggle be-

tween the primary and seconday satellites for either
DISH Network or DIRECTV.  Both have program-
ming on more than one satelite.When a channel is
selected on the remote control  and is not on the
satellite currently selected, the unit will automati-
cally move to the correct satellite.

DIRECTV programming

1. DIRECTV receivers must be set for oval dish 2
sat selection to enable toggling between primary
101°W satellite and alternate 119°W satellite only.
(Consult receiver manual for procedure.) After
receiver is set for the correct dish selection, when
you request a channel located on a different satel-
lite, the unit will automatically move to that
satellite.

DISH Network programming (DISH 500)

DISH Network receivers must have the “SW42”
switch installed in order to toggle between the pri-
mary 119 satellite and the alternate 110 satellite.
(Consult your receiver manual for the procedure to
reach the “check switch” menu.)

To install the “SW42” switch:

1. Before turning on your MV-4002 system, make
sure that your satellite receiver and television are
turned on and your receiver is on the “point dish”
menu. (Consult your owner’s manual to reach this
menu.)
2.  While the vehicle is stationary, turn on the MV-
4002 system and wait for signal acquisition on
satellite 119.
3. After signal is acquired, the system will continu-
ously track the signal for approximately 6 minutes.
At the end of 6 minutes, the unit will enter sleep
mode. You now have 6 minutes to complete
Check Switch test. Consult your receiver manual
for instructions on running this test. Be sure that
Superdish and Alternate are unchecked if applicable.
Onscreen options may vary by receiver.

4. During the Check Switch Test, the receiver will
begin checking the switch by toggling between
satellites. When this is completed, SW42 will ap-
pear on the screen. It will be at the top of the
screen, satellite designations will be below, show-
ing odd and even transponders. See illustration.

If a switch other than SW42 appears, or you
have an X  in one of the boxes below the satel-
lites, repeat Check Switch Steps.

5.  Your system is now set up to toggle between sat-
ellites. It will automatically move to the correct
satellite when a channel is selected with your remote
control.

NOTE:  Once these steps are completed, you
won’t have to perform this test again, unless
Check Switch was performed on another satel-
lite dish, such as a home dish.

Check Switch screen display

Install Summary

Input:            1         1          1         1
Satellite:     

119      119     110     110

Polarity:     

Odd   Even   Odd    Even

Status:           Satellite reception verified

Superdish                    Alternate

Cancel         

Test          Help

SW42

NOTE:  Be sure the “Superdish” and “Alter-
nate” boxes  ARE NOT checked.

Toggle: Your Winegard Automatic
satellite dish will move from the
primary to the alternate satellite in
order to receive multi-satellite
programming.

!

Summary of Contents for Movin' View MV-4002













Reviews: