JACKING MACHINE
86037580 GLIDE 01/03/07
4-16
MACHINE JACKING
The machine may be jacked up for service or
inspection by using the specified jack locations.
Always block the tires when jacking up the machine.
FOR SAFETY: Before leaving or servicing
machine; Stop on level surface, set parking
brake, turn off machine and remove key.
The rear jack points are the frame just behind the
rear wheels. Remove the squeegee tool before
jacking.
NOTE: See Squeegee Tool Removal in Maintenance
Section.
The front jacking point is the front bumper.
TO JACK UP MACHINE
1.
Empty the recovery and solution tank.
2.
Turn the key switch off and set the parking brake.
FOR SAFETY: Before leaving or servicing
machine; Stop on level surface, set parking
brake, turn off machine and remove key.
3.
Block the tires that are not being raised to
prevent the machine from rolling.
FOR SAFETY: When servicing machine, block
machine tires before raising machine.
4.
Using a jack of adequate capacity. Raise the
machine using the designated jack points.
FOR SAFETY: When servicing machine, use hoist
or jack of adequate capacity, jack machine at
designated jack locations only. Block machine
with jack stands when raised.
5.
When machine is raised, use jack stands at the
designated jack locations.
Support the front of the machine by placing jack
stands or solid wood blocks under the U-shaped
stabilizer bars.
FOR SAFETY: Block machine at designated jack
locations with jack stands when raised.
6.
Slowly lower the machine onto the jack stands.
7.
Be sure that the machine is secure.
8.
Service or inspect the machine as required.
9.
When finished working on the machine, raise the
machine off the jack stands.
10.
Remove the jack stands.
11.
Lower the machine to the floor. Block wheels as
they are lowered.
12.
Remove wheel block after machine has been
completely lowered.
MACHINE STORAGE
If the machine is to be stored for extended periods of
time, the following steps must be taken to minimize
the chance of corrosion or deposits forming.
1.
Drain both solution and recovery tanks. Clean
soil and chemical build up from tank. Flush with
clean water including the solution delivery
system. Leave solution tank lid and recovery
tank dome open.
2.
Raise the rear squeegee assembly and the scrub
deck.
3.
Remove brushes and rinse with clean water. Dry
thoroughly.
4.
Wash squeegee blades with clean water.
5.
Park the machine in a cool, dry area.
6.
Check the charge level of the batteries monthly.
Recharge when batteries drop below 25%
charge.
If suitable space exists to store batteries from
machine, remove from machine.
7.
Perform next lubrication interval.
Summary of Contents for 10052450
