Winco ULPSS20B2W/A Installation And Operator'S Manual Download Page 28

2270-00

28

60706-229

WINCO, Incorporated warrants to the original purchaser for 2 months or 000 hours, 

which ever occurs first, that goods manufactured or supplied by it will be free from de-

fects in workmanship and material, provided such goods are installed, operated and 

maintained in accordance with WINCO written instructions.

WINCO’s sole liability, and Purchaser’s sole remedy for a failure under this warranty, 

shall be limited to the repair of the product.  At WINCO’s option, material found to be de-

fective in material or workmanship under normal use and service will be repaired or re-

placed.  For warranty service, return the product within 2 months or 000 hours, which 

ever occurs first from the date of purchase, transportation charges prepaid, to your near-

est WINCO Authorized Service Center or to WINCO, Inc. at LeCenter Minnesota.

THERE IS NO OTHER EXPRESS WARRANTY.

To the extent permitted by law, any and all warranties, including those of merchantability 

and fitness for a particular purpose, are limited to 2 months or 000 hours, which ever 

occurs first from date of purchase.  In no event is WINCO liable for incidental or conse-

quential damages.

Note:  Some states do not allow limitation on the duration of implied warranty and some 

states do not allow the exclusion or limitation of incidental or consequential damages, so 

the above limitations may not apply in every instance.  This warranty gives you specific 

legal rights which may vary from state to state.

WINCO reserves the right to change or improve its products without incurring any obli-

gations to make such changes or improvements on products purchased previously.

EXCLUSIONS:

WINCO does not warrant Engines.  Engines are covered exclusively by the warranties 

of their respective manufacturers, see enclosed warranties.

WINCO does not warrant Batteries, or Other Component Parts that are warranted by 

their respective manufacturers.

WINCO does not warrant modifications or alterations which were not made by WINCO 

Inc.

WINCO does not warrant products which have been subjected to misuse and/or negli-

gence or have been involved in an accident.

12 MONTH LIMITED WARRANTY

Summary of Contents for ULPSS20B2W/A





























Reviews: