Winco TransMotion TMM5 PLUS Series Operation Manual Download Page 6

Document No.: TMM-2220-13 

Revision:  A 

Page 6 of 30 

 

ACCESSORY WARNINGS: 

 

  To prevent serious injury and property damage, review operating manuals of all medical equipment and 

accessories that may be used with, or attached to, this chair. 

 

  Using the supplied accessories in the incorrect manner may cause patient, bystander, or facility harm. 

 

  If chair is equipped with accessory belts, refer to appropriate Field Installation and Usage Instructions 

(provided with belts) for proper installation, use, and care. 

  

  To prevent fire hazards, follow all precautions and operating procedures prescribed by suppliers of oxygen 

administering equipment (i.e. oxygen gas regulators, tents, masks, cannulas, etc.)   

 

  To prevent injury and property damage, total weight of items placed on “IV” pole must be less than 25 lbs.    

 

  If mounting accessories to back surgical rails, ensure accessory is properly installed and securely engaged 

prior to transporting patient/chair, and prior to use. Only equipment approved by TransMotion by Winco is 

to be mounted on surgical rails. TransMotion by Winco is not responsible for damage, and assumes no 

liability, caused by the use of unapproved equipment or accessories.  Approved medical equipment 

includes tools, instruments, or scopes that are compatible with a.365” thick by 1.125” wide surgical rail. 

 

CAUTIONS:

 

 

 DO NOT MODIFY CHAIR 

 

  Modifying chair can cause unpredictable operation resulting in injury to patient, medical personnel, or 

bystander.  Modifying chair will void warranty. 

 

 USE SAFE OPERATING PROCEDURES 

 

  Prior to operating chair, ensure patient clearance by moving any overhanging equipment, or moving chair 

from under a table, to prevent patient injury. 

  For TMM5X PLUS, chair must be at least 20 inches from nearest wall or obstruction to allow for full range 

of activation. 

  Leave chair in lowest position whenever possible.  This practice will decrease potential injury during an 

unsupervised patient egress from chair. 

  Prior to patient transport in chair, raise side rails and ensure latching mechanism is in locked position.  

Medical personnel must determine degree of restraint needed to ensure patient’s safety during transport. 

 

For “F” Option Only 

Since footrest is foldable (not locked in position), ensure protection of patient’s feet while moving chair in 

close quarters (i.e. elevators, crowded hallways, procedure rooms).    

 

 

 

 INSPECT AND CLEAN CHAIR REGULARLY 

 

  Inspect cushions after each use.  Discontinue use if upholstery is ripped, cut, or torn, which could allow 

fluids to enter cushion.  This practice will prevent infection of patients and medical personnel and 

contamination of medical equipment. 

  Do NOT use machine / pressure / power wash procedures on chair.  After each use in a clinical setting, 

hand wash all patient-contact surfaces (i.e. cushions, rails) and plastic base cover with warm water and 

mild detergent.   

 

For “A” Option Only 

For large fluid spills on chair, immediately unplug chair from AC wall outlet. 

 

 

 

 

Summary of Contents for TransMotion TMM5 PLUS Series
































Reviews: