Winco S300 Stretchair Owners Operating & Maintenance Manual Download Page 3

IMPORTANT - PLEASE READ

Read all instructions before using this product.

IMPORTANT SAFETY INSTRUCTIONS

    

-     SAVE THESE INSTRUCTIONS

To reduce the risk of electric shock when using an electrical appliance, basic 

precautions should always be followed, including the following:

DANGER: Always unplug this product from the electrical outlet before cleaning, maintenance or

                  when putting on or taking off parts.

     WARNING:

1.  Unplug this product from the electrical outlet if this product is not being used for extended 

     periods of time.

2.  Supervision should be provided when this product is used by, on, or near children, invalids, or

     disabled persons.

3.  Use this product only for its intended use as described in this manual.  Do not use attachments

     that are not recommended by the manufacturer.

4.  Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has

     been dropped or damaged, or dropped into water.  Contact your Winco authorized dealer.

5.  DO NOT carry or pull this product by power supply cord or use the cord as a handle.

6.  Keep the cord away from heated surfaces.

7.  Do not use outdoors.

8.  To disconnect, turn all controls to the "off" position, then remove plug from outlet.  Do not "yank"

     cord.

9.  Clean electrical components with a damp cloth only – Warranty will be VOID if liquid is 

     introduced into electrical components

10.  Use only a certified extension cord that is rated at 15 amperes; extension cords rated for less

       amperage may over heat.  Care should be taken to arrange the cord so that the cord cannot

       be pulled or tripped over.

11.  DO NOT run chair or other equipment over cord.

12.  This chair comes with a grounded three blade plug, if the plug does not fit into the outlet; 

       contact a certified electrician to install the proper outlet.  DO NOT MODIFY THE PLUG IN ANY

       WAY.

DANGER: KEEP DRY - Do not operate in a wet condition or environment.

WARNING: Connect this product to a properly grounded outlet only.  

2

Summary of Contents for S300 Stretchair





















Reviews: