WilTec ARTICLE 60252 Operation Manual Download Page 2

The information contained in this document is subject to change without prior notice. No part of this
document can be copied or duplicated in another form without

 

the prior written consent of  WilTec

Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in
this user manual or the connection diagram.
Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual
is complete, accurate and updated, errors cannot always be avoided.  In the event of problems with
this user manual please complete and send this form back to us.

FAX-notification (++

+49 2403 55592-15

), 

 
from: ________________________________________
 
Name: 

________________

 

Firm:

_____________________

 

Tel/Fax:

__________________

 

I would like to report the following mistakes: 

 
 
 
 

_______________________________

 

 ____________________________________

 

 

 

Customer Service WilTec Wildanger Technik GmbH 
e-mail: 

[email protected]

Tel:++ +49 2403 55592-0

Introduction

Thank you for purchasing this quality product.

  To minimize the risk of injury by means of fire or

electric shock we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you have understood its
content.

Always use a grounded power connection with the appropriate mains voltage. You can
find the corresponding mains voltage on the type plate. If you have any doubts about the

connection   being   grounded,   have   it  checked  by  a  qualified   professional.  Never   use   a
faulty electric cable.

Do   not   inspect   the   electrical   part   of   the   pressure   pond   filter   in   a   wet   or   damp
environment or when you are wet yourself and protect it from direct sunlight. Install this

device in a safe location so that nobody can step on the cable, fall over or damage it.
Disconnect the power plug before cleaning it and use only a damp cloth for cleaning.
Avoid using cleaning agents and 

make sure that no liquid enters the electrical part of the pump.

The electric part of the device contains no parts that can be inspected or serviced by the user. Leave
the   maintenance,   adjustment   and   repair   to   qualified   technical  personnel.   In   case   of   unauthorised
intervention the 2-year warranty is no longer valid! Keep these operation instructions safe.

© by WilTec Wildanger Technik GmbH 

Seite 12 

http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Summary of Contents for ARTICLE 60252











Reviews: