WilTec ARTICLE 60252 Operation Manual Download Page 10

Disposal regulations

EU   guidelines  regarding   the   disposal  of   scrap   electric   appliances  (WEEE,   2012/19/EU)   were
implemented in the law related to electrical and electronic equipment and appliances.

All WilTec electric devices that fall under the WEEE regulations are labelled  with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.

The company WilTec Technik GmbH has been registrated in  the German registry  EAR under the
WEEE-registration number DE45283704.

Disposal of used  electrical and electronic  appliances
(intended   for   use   in   the  countries   of   the   European
Union and other European countries  with a separate
collection system for these appliances).
The logo on the article or on  its packaging points out
that   this   article   must   not   be   treated   as   normal
household waste but must be disposed to a recycling
collection   point  for   electronic  and  electrical  waste
equipment. By contributing to the correct disposal of
this article you protect the environment and the health
of   your   fellow   men.   Environment   and   health   are
threatened by inappropriate disposal.

Materials’ recycling helps reduce the consumption of raw materials.

Additional information on  recycling this article can be provided by your  local community,  municipal
waste disposal facilities or the store where you purchased the article.

Address:

WilTec Wildanger Technik GmbH

Königsbenden 12 / 28

D-52249 Eschweiler

Important notice:

The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions
manual require the written permission of WilTec Wildanger Technik GmbH.

© by WilTec Wildanger Technik GmbH 

Seite 20 

http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Summary of Contents for ARTICLE 60252











Reviews: